Calculate the steady state hcho concentration

Assignment Help Civil Engineering
Reference no: EM13560459

Formaldehyde (HCHO) is a  known human carcinogen and causes a variety of health effects. Formaldehyde can be introduced to indoor air from a new carpet, fiberboard,  and other building materials.  After Hurrican Katrina in 2005, the Federal Emergency Management Agency (FEMA) provided 100,000 trailers and mobile homes for displaced gulf coast residents. Unfortunately, those trailers were built with materials that emitted high levels of formaldehyde. Testing in 2007-2008 found an average indoor formaldehyde of 95 ug/m3 with a range of 4-730 ug/m3 (https://www.cdc.gov/nceh/ehhe/trailerstudy/assessment.htm) Adverse respitory effects are observed when formaldehyde is greater than or equal to 120 ug/m3.

Assume the average trailer volume is 70m3 and the air changes 2.5 per hour (ach). The decay constant for formaldehyde is 0.4/hour and the ambient outdoor concentration is 2 ug/m3

A) calculate steady state emission rate that gives you 95 ug/m3

B) These concentrations were measured when the trailers were 2 years old and the emission rate had significantly decreased by that time. New material rates as high as 290 mg/hr have been reported. Calculate the steady state HCHO concentration (ug/m3) resulting from that emission rate.

C) Compare the answers for threshold adverse respitory effects

Reference no: EM13560459

Questions Cloud

One side slope extends to a height of 7.8 m above the bottom : A uniform earth canal in good condition is 17 m wide at the bottom and has side slope of 2 horizontal to 1 vertical. One side slope extends to a height of 7.8 m above the bottom level and the other side extends to an elevation of 1.8 m then extends t..
What the order of accuracy of this operator : You are given five data points, yi = f(xi), where i ranges from -2 to 2, and where xi+1 ? xi = ?x is a constant. You are interested in computing the first and second derivative of f at x0.
Determine the operating point on the pump characteristic : Determine the operating point on the pump characteristic curve when the flow is such that the pressure drop across the control valve is 35 kN/m^2
Determine the flow rate in the pipeline and the head loss : Contract loss coefficient = Kc = 0.34 , d1 = 2 in , d2 = in d3 = 1 in , and Rm = 6ft , gauage fluid = 52lbf/ft^3 neglect friction but consider an expansion loss coefficient of k' = o.5
Calculate the steady state hcho concentration : These concentrations were measured when the trailers were 2 years old and the emission rate had significantly decreased by that time. New material rates as high as 290 mg/hr have been reported. Calculate the steady state HCHO concentration (ug/m3) re..
How efficient is the pump : A fireboat pump draws seawater (density=1.95 slugs/ft^3) from a 6 inch diamter submergred pipe that reaches 6 feet under the free surface and discharges 120 ft/s through a 2 inch diamter nozzle 10 feet above the free surface
Find the rate of biological growth : Two identical complete-mix activated sludge units are connected in series; one-half of the sludge recycle flow rate, QR, is recycled to the primary effluent pipeline which handles a flow rate Q, and the other half is recycled to the effluent line fro..
Which alloy and in what condition whould you choose : For a concrete column that is part of a braced frame, if the column is square, tied, 18 inches per side, 16 feet long, classify the column as slender or non slender
For a concrete column that is part of a braced frame : For a concrete column that is part of a braced frame, if the column is square, tied, 18 inches per side, 16 feet long, classify the column as slender or non slender. Assume that at one end of the column a clockwise moment of 100 k-ft is present

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine what should the viscosity of the model fluid be

In the late 1990's the U.S. Army Corps of Engineers designed an experiment to model the flow of the Tennessee river downstream of the Kentucky Lock and Dam.

  What size of corrugated-metal pipe culvert would be selected

A culvert under a road must be 35m long, have a slope of 0.0035 and carry 4m^3/s. The crown of the roadway is 4.2m above the culvert invert. Assume the outlet will discharge freely.

  Determine the forces acting on member bh

The force exerted by the potatoes on the frame at one side of the chair is equivalent to horizontal and vertical forces of 24 N and 84 N, respectively, at E and a force of 28 N perpendicular to member BH at G.

  At what temperature does the first solid phase formwhat is

1.at what temperature does the first solid phase form?2.what is the composition of this solid phase?3.at what

  Determine depth result upstream during design flood event

A 1.5m diameter barrel (concrete barrel, well-rounded entrance) that is 20 m long is installed on a slope of 2 percent. The design discharge is 9.5 m^3/s and the inlet will be submerged but not the outlet.

  Find pounds of ferric hydroxide are theoretically produced

(a) how many pounds of ferric chloride per million gallons are used (b) how many pounds of hydrated lime per million gallons are used, assuming a purity of 70 % CaO

  Explain how to determine the power input to the pump

Water enters the pump of a steam power plant as saturated liquid at 20 kPa at a rate of 45 kg/s and exits at 6 MPa. Neglecting the changes in kinetic and potential energies and assuming the process to be reversible

  Determine the crest height of a suppressed weir that should

A weir is to be installed to measure flows in the range of 0.5 to 1.0 m3/sec. If the maximum (total) depth of water that can be accommodated at the weir is 1m and the width of the channel is 4m, determine the crest height of a suppressed weir that sh..

  Calculate equivalent pipe size and flow in the pipe

The first pipe of 400mm diameter is 500 m long, the second pipe 600 m long, size 300mm, and the last pipe is 500m long of diameter 200mm. If the elevation difference between two reservoirs is 30m

  Maximum acceptable tensile service load

Compute the maximum acceptable tensile service load T that may act on a single angle L6x4x3/4 that is welded along only one leg to a gusset plate; thus, there are no holes. The service load is three times the dead load. Solve for a0 A36 steel.

  Round up yellow and all-red times to the nearest ½ second

Determine the appropriate yellow and all-red interval to use for each phase. Assume a 10 ft/sec2 deceleration rate, a one second reaction time, and a 20 ft. vehicle length. Round up yellow and all-red times to the nearest ½ second.

  Determine va and the time of the flight

The skateboard rider leaves the ramp at A with an initial Velocity Va at a 30 degree angle. If he strikes the ground at B, determine Va and the time of the flight.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd