Calculate the speed of the water relative to the hydrofoil

Assignment Help Civil Engineering
Reference no: EM13550434

A two dimensional flow field is defined by u = x^2 - y^2 and v = -2xy. Is the flow rotational or irrotational?A speedboat on hydrofoils is moving at 20 m/s in a freshwater lake. Each hydrofoil is 3 m below the surface. Assuming, as an apporximation, frictionless, incompressible flow, find the stagnation pressure(gage) at the front of each hydrofoil. At one point on a hydrofoilm the is -75kPa(gage). Calculate the speed of the water relative to the hydrofoil at this point and the absolute water speed.

Reference no: EM13550434

Questions Cloud

The basin dimensions if increments of 1.0 inch are used : A rapid-mixing basin is to be designed for a water coagulation plant, and the design flow for the basin is 4.0 MGD (million gallons per day). The basin is to be square with a depth equal to 1.25 times the width.
Determine by trigonometry the magnitude and direction : Two parallel disks of diameter D are brought together, each with a normal speed of V. when their spacing is h, what is the radial component of convective acceleration at the section just inside the edge of the disk (section A) in terms of D, V, and h..
You are paying into a mututal fund that earns compound : You are paying into a mututal fund that earns 6% compound interest. If you are making an annual contribution of $10000, how much will be in the funds in 20 years? What if the fund makes 10%? What if it loses 5% per year?
Determine the required cstr volume v (gallons) : Determine the required CSTR volume, V (gallons), and hydraulic residence time, t = V/Q (hours), to comply with the current industrial pre-treatment permit limitation for phenol.
Calculate the speed of the water relative to the hydrofoil : A two dimensional flow field is defined by u = x^2 - y^2 and v = -2xy. Is the flow rotational or irrotational?A speedboat on hydrofoils is moving at 20 m/s in a freshwater lake
What is the significance of the compresive strength : If the pulleys are fixed to the shaft, determine the magnitude of the tension T and the x,y,z componenet sof reaction at the smooth thrust bearing A and smooth journal bearing B.
Calculate the hydraulic conductivity k of the soil sample : A falling head permeability test was carried out on a 15 cm long sample of silty clay. The diameter of the sample and the standpipe were 9.8 cm and 0.75 cm, respectively. The water level in the standpipe was observed to fall from 60 cm to 45 cm in 12..
Which chemical will be transported the farthest downgradient : Groundwater has been contaminated with three chemicals: benzene (log Kow 2.13), pentachlorobenzene (log Kow 5.03), and naphthalene (log Kow 3.36). The aquifer (rs = 2.3 g/cm3; h = 0.4; foc = 0.02)
Determine the mass flow rate of the cooling water : Refrigerant 134a is compressed at steady state from 2.4 bar, 0 degrees celcius, to 12 bar, 50 degrees celcius. Refrigerant enters the compressor with a volumetric flow rate of 0.38m^3/min, and the power input to the compressor is 2.6 kW.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine what is the first-order decay rate constant

A minimum contact time of 30 min is required to reduce the pathogen concentration from 100 pathogens/L to below 1 pathogen/L through a first-order decay process. You plan on treating water at a rate of 1,000 gal/min.

  What is the velocity of striking

If the ball strikes the side of the building 2s after being thrown, at what height above the base of the building did the ball strike the building? What is the velocity of striking?

  Determine the moment of the l6-n force about point b

A foot valve for a pneumatic systemis hinged at B. Knowing that a=28degrees, determine the moment of the l6-N force about point B by resolving the force into horizontal and vertical components

  Derive the equation for a slightly compressible fluid

Assume that there is only one phase present and that the formation is homogeneous, but anisotropic. Further, assume that viscosity, formation volume factor, and the areas available for flow are constant spatially. Last, assume 3-D flow using x, y,..

  How much was invested in each account

Suppose a person invests a total of $10,000 in two accounts. One account earns 8% annually, and the other earns 9% annually. If the total interests earned from both accounts in a year is $860, how much was invested in each account?

  Calculate the largest tolerable internal crack length

Calculate the largest tolerable internal crack length for a 7075-T651 aluminum alloy component that is loaded to a stress one-half of its yield strength without catastrophic fracture. For the alloy, the plane strain fracture toughness is 24 and yi..

  Calculate the trip generation of the zone in th cbd

A zone in the CBD is projected to contain 1,525,000 ft2 of residential space; 3,675,000 ft2 of service establishments; and atotal retail activity floor area of 2,100,000 ft2.

  Find what must be the composition in copper-nickel alloy

It is desirable to produce a copper-nickel alloy that has a minimum noncold-worked tensile strength of 390 Mpa and a ductility of at least 40% elongation. Is such an alloy possible If so, what must be its composition

  Determine the components and magnitudes of the vectors ab

In order to move a wrecked truck, two cables are attached to the truck at A and pulled by winches B and C as shown. Determine the components and magnitudes of the vectors AB and AC

  What is the concentration of mlvss in the activated sludge

The concentration of Chemical Oxygen Demand (COD) in the effluent from this system is 25 mg L-1. The growth rate of the organisms in this case is 0.9 days-1. The activated sludge tank has a volume of 50 m3 and the flow rate through it is 500 m3 da..

  Detail description of staircase

Detail description of Staircase with it's plan, design criteria about it for various types of buildings,standerd dimensions of rise & going of stair which is applicable in civil engineering works

  How many hours should be taken an articulated wheel loader

How many hours should it take an articulated wheel loader equipped with a 4 yd3 bucket to load 3,000 yd3 of gravel from a stockpile into rail cars if the average haul distance is 300 feet one way

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd