Calculate the size of defect that will result

Assignment Help Mechanical Engineering
Reference no: EM131065938

ultrasonic testing of an aircraft engine component revealed maximum internal defects of 3mm length. theses defects will grow under cyclic loading until they become critical in length. given the following information, calculate the size of defect that will result in fast fracture after 100 million cyclic . assume a pairs exponent of 3 , actress amplified of 5 mpa and a material constant , A of 4 x 10^-11?

Reference no: EM131065938

Questions Cloud

How this political divide would evolve into two-party system : After choosing which side to support, use the PowerPoint reading from this unit to choose a minimum of four of the six bullets from slide two titled, "Quick Comparison," as the basis for your speech. Using these four bullets you have selected summ..
The balance sheet of cheese wheel company : The following information is taken from the balance sheet of Cheese Wheel Company: Depreciation expense of $15,000 was reported on the 2012 income statement.
Tools of supply and demand : The market for health care services can be examined using the tools of supply and demand. In this market, the quantity variable is hours of health care services. Consumers' demand health care services while doctors (or others) supply health care s..
Information for a monopoly firm : Consider the following information for a monopoly firm. Assume that Q equals the level of output and all costs are economic costs.
Calculate the size of defect that will result : calculate the size of defect that will result in fast fracture
Plants and developing a flexible manufacturing system : Tombro Industries is in the process of automating one of its plants and developing a flexible manufacturing system. The company is finding it necessary to make many chages in operating procedures.
Which are better left in the dustbin of history : Most prehistoric cultures were matricentric and not patriarchal - that is, the role of women was more central, or more powerful, than the role of men. What aspects of matricentrism (if any, in your opinion) should be revived in our modern patriar..
Economy grow between two years : Suppose that nominal GDP in year 1 is 200 and nominal GDP in year 2 is 242 .Assume that inflation is 10 percent per year. How fast did the economy grow between these two years?
Actions of government work : Describe the role government should play in correcting for market failures. Make sure to apply Saint Leo's Core Values to your analysis, remembering that responsible stewardship calls on us to be ‘resourceful'. You should cite specific examples..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The accerleration of a particle is defined by the relation

the accerleration of a particle is defined by the relation a a - 6t2 where a is constant. at t 0 the particle starts

  Volumetric flow rate of air into the cooler

In a device to produce potable water, humid air at 90°F, 29.7 in Hg, and 95% relative humidity is cooled to 40°F at constant pressure. What volumetric flow rate of air into the cooler (ft3/min) is required to provide 10.0 gal/mm of condensed water..

  Small angular oscillations of bar about the vertical axis

A uniform bar of length l and weight w is suspended symmetrically by two strings, set up the differential equation of motion for small angular oscillations of the bar about the vertical axis, and determine its period.

  Compute the maximum bending stress at mid-span

Calculate the maximum bending stress at mid-span, and, for the same section, locate the neutral axis. Neglect the weight of the beam

  Assume that a jet touches down 170 mph and its speed is

assume that a jet touches down 170 mph and its speed is reduced to zero in 240 ft. assuming a constant deceleration

  Determine the mass of ice

In an effort to cool a 12-fluid-oz drink in a can, a person grabs the can and starts shaking it in the iced water of the chest at 32°F. Using the properties of water for the drink, determine the mass of ice that will melt by the time the canned dr..

  Describe the printed circuit heat exchanger

Compact heat exchangers (CHEs) were among the first unit operations to be classified as intensified - Describe the Printed Circuit Heat Exchanger (PCHE) and its merits and potential uses.

  Determine the magnitude and direction of the resultant

The boom OA carries a load P and is supported by two cables as shown. Knowing that the tension is 510 N in cable AB and 765 N in cable AC, determine the magnitude and direction of the resultant of the forces exerted at A by the two cables.

  Horizontal chromium-plated surface

Saturated ethylene glycol at 1 atm is heated by a horizontal chromium-plated surface which has a diameter of 200 mm and is maintained at 480 K. Estimate the heat- ing power requirement and the rate of evaporation.

  The water emerges from the boiler and flows into the

water at 10 kpa and 40 c enters the pump of a rankine cycle. the pump has an effiiciency of 82 and pumps the water up

  The diameter of the rod is 25mm internal diameter and its

a long rod is exposed at air at 298oc. it is heated at one end. a steady state condition the temp at 2points along the

  Derive the terminal velocity v0 when acceleration becomes

a sphere of solid density rho s and diameter d is dropped to a water pond density rho s and viscosity mu. initial

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd