Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
a single span of an overhead line is 250 ft in length, having the supporting poles at the same level. the maximum tension in the conductor is 855 lb. the weight of conductor is 0.125 lb/ft.
Calculate the sag:
A-using the catenary method
B-using the parabolic method
1. What is the force on a 10 cm wire carrying 1.0 A in a uniform magnetic field of 500 gauss 2. In the above example, if the current is in a loop of width 6.0 cm and the coil lies in the plane of magnetic flux, what is the torque on the loop
How do we determine the overall gain of a cascaded system of AV1, AV2, and AV3 in dB, in absolute What do we do if all the gains are given in dB, absolute and dB
An InP TED is 0.5 pm long with a cross sectional area of 10" cm2 and is operated in the transit-time mode.(a) Find the minimum electron density no required for transit-time mode.
The following heat engines produce power of 95,000 kW. Determine in each case the rates at which heat is absorbed from the hot reservoir and discarded to the cold reservoir. A Carnot engine operates between heat reservoirs at 750 K and 300 K.
Design and implement a Rectangle class. Make your class inherit from the Point class given in the lecture (notice that a rectangle can be described through the upper-left vertex, the height, and the width).
Design the basic interface circuit (using an op amp) for a temperature sensor that covers a range of 0 degrees to 70 degrees C if the output of the sensor is 2 mV/1C and the ADC voltage range is 0 to 4 V.
A PLL frequency synthesizer has a variable -modulus prescaler of M=10/11 and divider ratios of the A and N COUNTERS OF 40 and 260. the reference frequency is 50khz. what are the VCO OUT PUT FREQUENCY and the minimum frequency step increment
A three-phase load is Y-connected. The load has a phase voltage of 139 V and a phase current of 49 A. Each phase of the load consumes 5.1 kW of power. (A) Sketch and label the load. Find (b) the line voltage, (c) the line current, and
Find the propagation delay for a minimum-size inverter for which Kn' = 3 Kp' = 180 uA/V^2 , and (W/L)n = (W/L)p = 0.75 um/0.5 um , VDD = 3.3 V , Vtn = -Vtp = 0.7 V, and the capacitance is roughly 2
Determine the left triceps muscle force (Ftri), elbow joint reaction force (Rj) required to hold this position along with any ground reaction forces (Rg) and/or reaction moments (Mg) in the hand. Show all necessary free body diagrams along with th..
A buffer amplifier with a gain of 1 V/V has an input resistance of 1M and an output resistance of 10 ohm. It is connected between a 1-V, 100-k ohm source and a 100-ohm load. What load voltage results and what are the corresponding voltage, current,..
a DC motor turns at a speed of 1460 rpm and produces an output torque of 3.0Nm. The DC voltage applied to the motor is 100V and a current of 5.1A flows through the motor. A. What is the efficiency of the motor
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd