Calculate the rms phase current and real & reactive power

Assignment Help Electrical Engineering
Reference no: EM13291704

A single phase AC circuit is conected to a 120V, 60Hz. The circuit impedance is Z=8+j6Ω at 60Hz. Calculate the rms phase current, real & reactive power and power factor.

Reference no: EM13291704

Questions Cloud

Compute the cv : The managers of Merton Medical Clinic are analyzing a proposed project. The project's most likely NPV is $120,000, but, as evidenced by the following NPV distribution.
How much work has the electric field done on this proton : Two very large charged parallel metal plates are 10.0cm apart, How much work has the electric field done on this proton by the time it reaches the positive plate
In a dihybrid cross between rrtt and rrtt : In a dihybrid cross between RrTt and RRtt, what are the genotypes and phenotype RATIOS of the offspring, assuming R and T are dominantt? R codes for round seed while r codes for wrinkled seed. T codes for tall height, while t codes for short height. ..
Find out the volumetric flow rate of air : A mixture of fuel containing 0.530 mol CH4/mol, 0.330 mol C3H8/mol, and 0.140 mol C5H12/mol at 60.0°C and 125 kPa (gauge) enters a furnace at a rate of 91.0 L/min where it reacts with 17.4% excess air.
Calculate the rms phase current and real & reactive power : A single phase AC circuit is conected to a 120V, 60Hz. The circuit impedance is Z=8+j6Ω at 60Hz. Calculate the rms phase current, real & reactive power and power factor.
What is the present value of your total lottery payments : Assuming an interest rate of 8%, what is the present value of your total lottery payments?
Find the string efficiency if a guard ring increases : The shunt capacitance of metal work ofeach insulator is 0.26C to earth and 0.15C to line. Find the stringefficiency if a guard ring increases the shunt capacitance to lineof the metal work of the lowest insulator to 0.35C.
What is the maximum torque that the loop can experience : A Single Turn, Square Loop A 0.408 m length of wire is formed into a single-turn, square loop in which there is a current of 14.3 A. What is the maximum torque that the loop can experience
What considerations might be important in the selection : A member of your board has asked if you have considered competitive bids for the distribution of your securities compared to a negotiated contract with a particular firm. What factors are involved in this decision?

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Explain the four main kinds of partial reinforcement

1. Explain the basic principles of classical conditioning using an experiment to illustrate how the principles are used. 2. In the operant conditioning school of behaviorism, what is partial reinforcement. Explain the four main kinds of partial rein..

  Design a single-stage 3-input compound cmos minority gate

A majority gate returns a true output if more than half of the inputs are true. So, a 3-input majority gate outputs a ‘1' if at least two of its inputs are ‘1'. A minority gate generates the complement, that is it outputs ‘0' if at least two of th..

  Deduce expression for power in terms of the line voltage

Show that the power in a three-phase, three-wire system with balanced loads is constant at every instant. Deduce an expression for the power in terms of the line voltage, line current, and the power-factor.

  Determine the sheet resistance and the contact resistance

Measuring the resistances of the resistors with lengths L1 = 10 µm and L2 = 30 µm, the following values are obtained: R1 = 365-ohm and R2 = 1085-ohm, respectively. If the width of the resistors is 5 µm, determine the sheet resistance and the contac..

  Determine the band width at which amplitude response drops

Use two different criteria for determining the effective bandwidth of e^(-t)u(t). Ad the bandwidth, use the frequency at which the amplitude response drops to 1% of its peak value (at w=0). Next use the 99% energy criterion for determine the band ..

  Find the real power absorbed by each of the impedances

he real power delivered by a source to two impedances, Z1=3+j4 ohm and Z2=10 ohm, connected in parallel, is 1100 W. Determine (a) the real power absorbed by each of the impedances and (b) the source current.

  Define complex voltage

Complex Voltage = 10-j20. try to convert it to polar coordinate with my Ti 89 but I keep getting my answers in arc tan.

  Find capacity of cascade connection of n-channel

Find the capacity of the cascade connection of n binary-symmetric channels with same crossover probability ε. what is the capacity when the number of channels n=2.

  Write phasor expression i for current using cosine reference

Write the phasor expression I for the following current using a cosine reference a.)i(t) = I0cos(ωt - π/6): b.) i(t) = I0sin(ωt + π/3):

  Explain half-wave rectifier

Half-Wave Rectifier, For the half-wave rectifier, the source is a sinusoid of 120 Vrms at a frequency of 60 Hz. The load resistor is 5 ohms. Determine

  How would that affect the hall field and the hall voltage

Adding dopants to a sample of silicon is found to reduce the Hall coefficient by a factor of 10 and increase the conductivity by a factor of 5. What effect has this dopant addition had on the mean free path

  Find value of the capacitor connected in parallel with load

120V, 60 Hz source is connected to a distribution line whose resistance, and inductive reactances are 0.1Ohm, j0.2 Ohm, respectively. Single phase, 2HP, 120V, 0.75 lagging pf. motor and 2.4Kw, 120V heater is connected in parallel.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd