Calculate the reynolds number based on the wire diameter if

Assignment Help Mechanical Engineering
Reference no: EM13644707

A hot-wire anemometer is a temperature-based instrument for measuring velocities in a flowing gas. The key component of the device is a very fine wire (diameter = 0. 0004 in. , length = 0. 20 in. ) that is electrically heated. The wire is positioned so that the air stream passes over it in cross flow. The heating of the wire is accomplished by ohm ic dissipation of electric energy, in the same manner that the wires of a toaster are heated. The ohm ic heating of the wire is 0. 0253 W, and the wire temperature is 147 F. In the steady state, this heat is transferred to the air flow. The air that passes over the wire has a temperature of 73 F and a pressure of 726 mm Hg. Required results: The velocity of the air flow. Calculate the Reynolds number based on the wire diameter. If the velocity were to be doubled, and the wire and air stream temperatures were maintained as stated, what is the required ohm ic dissipation?

Reference no: EM13644707

Questions Cloud

A neon atom m 200 u makes a perfectly elastic collision : a neon atom m 20.0 u makes a perfectly elastic collision with another atom at rest. after the impact the neon atom
How many liters of the antifreeze ethylene glycol c2h6o2 : how many liters of the antifreeze ethylene glycol c2h6o2 would you add to a car radiator containing 6.50 l of water if
An engineering department consists of15 electrical 15 : an engineering department consists of15 electrical 15 chemical 15 industrial and 15 civil engineers. an
A solution is made from 96 g of a nonvolatile solute in : a solution is made from 96 g of a nonvolatile solute in 80.0 grams of water. the solution has a vapor pressure of .312
Calculate the reynolds number based on the wire diameter if : a hot-wire anemometer is a temperature-based instrument for measuring velocities in a flowing gas. the key component of
A 1000 kg safe is held 2 m above a heavy duty spring when : a 1000 kg safe is held 2 m above a heavy duty spring when the rope holding it breaks. the safe compresses the spring 50
Of 900 customers surveyed 414 said they were very : 1. of 900 customers surveyed 414 said they were very enthusiastic about a new home deacutecor scheme. construct a 99
As well as 3 fractions of a mixture of hexaneamp heptane : distillation was performed. 3 fractions of a mixture of octane amp hexane were taken. as well as 3 fractions of a
To help your restaurant marketing campaign target the right : 1. to help your restaurant marketing campaign target the right age levels you want to find out if there is a

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd