Calculate the required value of resistance

Assignment Help Other Engineering
Reference no: EM131195693

Problem 1:

The tuner for an FM radio requires an RLC series resonance band-pass filter with a resonance (central) frequency of 100 MHz (frequency of the FM station) and a bandwidth of 2 MHz. The aim here is to design a filter capable of passing the signals from the FM broadcast radio while rejecting the interfering signals from amateur radios and Military aircraft radios. The usual frequency bands reserved for the use of amateur radio is around 50 MHz and the frequency bands reserved for the use of Military aircraft radio is around 200 MHz.

a.) Calculate the:

i. magnification factor Q of the filter

ii. required value of inductance L

iii. required value of capacitance C

iv. required value of resistance R

v. cut-off frequencies

vi. Prove that the interfering signal originated from amateur radio at 50 MHz is reduced by at least 95%.

vii. Prove that the interfering signal originated from military aircraft radio at 200 MHz is reduced by at least 95%.

b.) Use Multisim to simulate your design and provide the complete circuit diagram of the filter (Please use screenshot).

c.) Provide the gain magnitude plot of your filter at the resonance frequency, the cut-off frequencies, the amateur radio frequency of 50 MHz, and the military aircraft radio frequency of 200 MHz. (Please use screenshot).

Problem 2:

Assuming that you have an ac power source of 10V (60Hz). Design a silicon based filtered full-wave bridge rectifier circuit that gives dc voltage output Vdc, varying at most ±5%. (If required use first diode approximation in your calculations.)

a.) Calculate the required value of resistance R b.) Calculate the required value of capacitance C

c.) Provide the complete circuit diagram of the rectifier circuit (including the values of R and C)

d.) Use Multisim to simulate the waveforms at the:

i. input and output of the transformer (use colour coding and labels),

ii. input and output of the rectifier (use colour coding and labels), for confirming that the requirements have been met

iii. Measure the average output dc voltage by using a multimeter. (Please use screenshot).

Problem 3:

Assume that you are working in America at a company that designs, tests, manufactures and markets various electronic instruments including dc power supply. The standard line voltage and frequency in America is 120V and 60 Hz, respectively. Your first assignment is to design an electrically isolated filtered Silicon based power supply that can produce dc output voltages of 9V±10% and -9V±10% with a maximum load current of 100mA. The voltages are to be switch selectable across one set of output terminals and the ripple voltage must not exceed 0.25V rms. Please use second diode approximation in your calculations.

a.) Calculate the:

i. required value of the load resistance RL
ii. required value of the capacitor C in order to fulfil the requirements of the circuit.

b.) Provide the complete circuit diagram of your design including the values of the each component, explain and justify your reasoning regarding your circuit design and values of the components used.

NB: You will need to use the mains as an input to your power supply and a transformer with one input and one output to the full-wave bridge rectifier. It is also preferable to use a surge resistance of 1Ω at the unfiltered output of the circuit in order to prevent too much current flow through the circuit. In order to simplify your calculations please neglect the effect of the 1Ω surge resistance.

Reference no: EM131195693

Questions Cloud

How define evm financial and costing management techniques : In a paper, provide a detailed explanation of how the knowledge gained in this course provided you with an understanding of a critical component of project management: EVM, financial and costing management techniques. How would you define EVM, fin..
Strategic interface between staffing-organizational planning : In Week 4, we examine a key responsibility in the HRM function, staffing. In his chapter we examine the strategic interface between staffing and organizational planning. We also review and discuss the various means used to screen candidates and co..
Prepare a table showing plums current ratio : Prepare a table showing Plum's  current ratio,  acid-test ratio, and  working capital after each transaction.
What is the advantage of using dimensionless products : what is the advantage of using dimensionless products for the experimental determination of correlations between quantities and for the graphical representation of functional dependences?
Calculate the required value of resistance : ENG1068 Electronic Instrumentation Calculate the required value of resistance and calculate the required value of capacitance - Provide the complete circuit diagram of the rectifier circuit (including the values of R and C)
Identify specific principles of servant leadership : Identify specific principles of servant leadership that, when employed effectively, can proliferate respect for multiculturalism and diversity within the organizations and communities they serve?
Kaufman five levels of evaluation : In chapter seven, three additional evaluation tools were introduced: the CIPP model of evaluation, Kaufman's five levels of evaluation, and CIRO. Choose one of the three models of evaluation. Describe the model. What are the advantages? What are t..
Determining the organizational-level goal : Identify an organizational-level goal that would be incorporated into an annual business strategy (e.g., financial performance, service, productivity, competitive advantage, innovation.).
Professional approach to shrm and ihrm : In what ways may a corporate and professional approach to SHRM and IHRM assist Emirates airlines to achieve its short term and long term strategic goals?

Reviews

Write a Review

Other Engineering Questions & Answers

  Characterization technology for nanomaterials

Calculate the reciprocal lattice of the body-centred cubic and Show that the reciprocal of the face-centred cubic (fcc) structure is itself a bcc structure.

  Calculate the gasoline savings

How much gasoline do vehicles with the following fuel efficiencies consume in one year? Calculate the gasoline savings, in gallons per year, created by the following two options. Show all your work, and draw boxes around your answers.

  Design and modelling of adsorption chromatography

Design and modelling of adsorption chromatography based on isotherm data

  Application of mechatronics engineering

Write an essay on Application of Mechatronics Engineering

  Growth chracteristics of the organism

To examine the relationship between fermenter design and operating conditions, oxygen transfer capability and microbial growth.

  Block diagram, system performance and responses

Questions based on Block Diagram, System Performance and Responses.

  Explain the difference in a technical performance measure

good understanding of Mil-Std-499 and Mil-Std-499A

  Electrode impedances

How did this procedure affect the signal observed from the electrode and the electrode impedances?

  Write a report on environmental companies

Write a report on environmental companies

  Scanning electron microscopy

Prepare a schematic diagram below of the major parts of the SEM

  Design a pumping and piping system

creating the pumping and piping system to supply cool water to the condenser

  A repulsive potential energy should be a positive one

Using the data provided on the webvista site in the file marked vdw.txt, try to develop a mathematical equation for the vdW potential we discussed in class, U(x), that best fits the data

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd