Calculate the re-circulating load in the secondary crusher

Assignment Help Civil Engineering
Reference no: EM13305578

A two stage crushing operation feeds 0.6 m diameter ore into a primary crusher at a rate of 25mt/hr. 80% of the ore feeds through an 0.2m screen into a secondary crusher. 65% of the ore from the secondary crusher comes out of a 50mm screen.

a. draw a basic flow diagram for this operation

b. calculate the re-circulating load in the primary crusher

c. calculate the re-circulating load in the secondary crusher.

Reference no: EM13305578

Questions Cloud

The food industry intentionally manipulates consumers : The food industry intentionally manipulates consumers by taking advantage of the fact that most consumers are ignorant of all of the ways that the food industry manufactures and processes its products.
What is the length of the spacecraft : A 20-m long spacecraft is passing by earth at 0.8c. What is the length of the spacecraft measured within the moving (spacecraft) referencee frame
What is the expected cost for the material over the life : Using the estimates from (a) & (b), what is the expected cost for the material over the life of the project using the COMPLEX method?
Calculate the re-circulating load in the secondary crusher : A two stage crushing operation feeds 0.6 m diameter ore into a primary crusher at a rate of 25mt/hr. 80% of the ore feeds through an 0.2m screen into a secondary crusher. 65% of the ore from the secondary crusher comes out of a 50mm screen.
How far horizontally off the edge does it hit the water : a student throws a rock with speed 20.0 m/s at 30 degrees off the edge of a cliff. how far horizontally off the edge does it hit the water
At what level of ebit eps be identical for plans i and ii : Blue Stripes Co. is comparing two different capital structures. Plan I would result in 9,000 shares of stock and $342,000 in debt. Plan II would result in 12,600 shares of stock and $205,200 in debt. The interest rate on the debt is 10 percent.
Calculate the mass flow rate for the concentrate stream : A magnetic separator processes 500 kg/hr of finely ground magnetite ore (Fe3O4). The ore containes 35% magnetite and an analysis of the concentrate and tailings shows that they contain 59.5% Fe and 3.8% Fe
What must be the power of the horns output to achive : a ship's horn can be heard above typical background noise if at intensity level 20 dB. what must be the power of the horn's output to achive this level at 5.0 km away

Reviews

Write a Review

Civil Engineering Questions & Answers

  Civil engineering - structure design

Structural design of reinforced cast in - place concrete - Structure design

  What is the total bod loading per day

The factory will use a 4 ft deep on-site lagoon to stabilize the waste with a loading rate of 20 lb BOD/acre-day. Part a) What is the total BOD loading per day?

  Calculate the quality of the steam exiting heat exchanger

A chemical plant uses a tube-­within-­a-­tube counterflow heat exchanger to heat air with the use of steam. During steady state operation, the air flows into the exchanger at a rate of 5,000 kg/h and a temperature of 27C and exits at a temperature..

  What is the difference between factor of safety

what is the difference between factor of safety in rankine & coulomb in overturning, sliding and bearing capasity ?

  Find distance particle will travel before coming to the rest

The acceleration of a particle is defined by the relation a= -0.7v where a is expressed in in/s2 and v in in/s. Knowing that t= o the velocity is 30in/s, determine 1.) the distance the particle will travel before coming to rest

  Determine the major and minor principal stresses at failure

Determine the major and minor principal stresses at failure and the effective stress friction angle (assume c' = 0). Plot the Mohr diagram.

  Calculate the axial stress in the copper and the steel

A steel flat bar of dimensions 4x1x12 inches is PINNED between two copper bars of dimensions 4x2x12 inches at room temp. The PINNED assembly is then cooled by 200 degrees fahrenheit.

  Determine the force to overcome static friction with table

A 15kg Block rests on top of a 25kg Block which is subject to a 400N force. Block B sits on a table. the Coeffiecents of friction are the same for all surfaces, u(s) is .4 and U(k) is .3. The force is Applied to the bottom block ( with no inclinat..

  Internal element of compression flange

what do mean by outstand element of compression flange, internal element of compression flange and web general

  Determine what is the present worth of benefit

A flood control project has a construction cost during the first year of $10 million, during the second year $6 million, and during the third year $2 million. It is completed at the end of the third year and thereafter incurs an annual operating c..

  Define flow at a hydraulic jump in terms of flow

Define flow at a hydraulic jump (upstream and downstream) in terms of the types of flow and corresponding Froude number. What is the depth of water at each section (upstream and downstream) compared to critical depth

  Determine the minimum necessary clearance height

Determine the minimum necessary clearance height of the overpass and the resultant elevation of the bottom of the overpass over the PVI. (ignore the cross-sectional width of the overpass)

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd