Calculate the ratio horizon

Assignment Help Electrical Engineering
Reference no: EM13867463

Part A:

1. A balanced transmission line picks up an undesired signal with a 5mW level. After coversion to an unbalanced signal using a center-tapped transformer, the undesired signal is 0.11 µW. Calculate the common mode rejection ratio, CMRR.

2. A fast rise-time 10-V step voltage is applied to a 50-Ω line terminated with an 80-Ω resistive load. Determine the reflection coefficient Γ, EF and Er.

3. Calculate the ratio horizon for a 500-ft transmitting antenna and a receiving antenna of 20ft. Calculate the required height increase for the receiving antenna if a 10% increase in the radio horizon were required.

4. An antenna has maximum forward gain of 14dB at its 108-MHz center frequency. Its reverse gain is -8dB. Its bandwidth extends from 55 to 185 MHz , calculate a) the bandwidth and b) the F/B ratio of the antenna.

5. Calculate the effective radiated power (ERP) of an antenna with a gain of 5 at a power of 0.5 kW.

6. The antenna in question 5 has a forward gain of 18dB and a reverse gain of 5dB, calculate the F/B ratio of this antenna.

7. A ship radio-telephone transmitter operates at 2738 kHz. At a distant point from the transmitter, the 2738 kHz signal has a measured field of 147 mV/m. the second harmonic field at the same point is measured as 405 µV/m. How much has the harmonic emission been attenuated below the 2738 kHz fundamental?

8. Calculate the maximum usable range for a radar system with PRT of 400 µs.

9. A green LED light source functions at a frequency of 5.7 * 1014 Hz, calculate its wavelength.

Part B:

1. A signal level of 0.4 µV is measured on the input to a satellite receiver. Express this voltage in terms of dBµV. Assume a 50-Ω system.

2. A microwave transmitter typically requires a +8dBm audio level to fully drive the input. If a +10dBm level measured, what is the actual voltage level measured? Assume a 600-Ω system.

3. If an impedance matched amplifier has a power gain (POUT/PIN) of 15, what is the value of the voltage gain (VOUT/VIN)?

4. Determine the deviation ratio for an FM system that has maximum possible deviation of 5 kHz and the maximum input frequency is 3 kHz. Is this narrow-or wideband FM?

5. A receiver with a 10 MHz bandwidth has a S/N of 5dB and a sensitivity of -96dBm.

6. What is the dynamic range (in dB) for a 12-bit PCM system?

7. Calculate the number of bits required to satisfy a dynamic range of 48dB.

8. The transmit power for digital communications device is 1W. The data rate is 28.8kbps. Determine the energy per bit.

9. A 56kbps NRZ-L encoded data stream is used in a digital communication link. Determine the minimum bandwidth required for the communications link.

Reference no: EM13867463

Questions Cloud

Explain maslow heirarchy of needs as it relates to work : Begin your essay by detailing a couple of incentive plans mentioned in the text and why you think they would or would not be effective. Then briefly explain Maslow's Heirarchy of Needs as it relates to work-life. What do you feel we might learn ..
Explain or analyze how the quote supports thesis : Explain or analyze how the quote supports thesis
Determine the molar entropy of mixing : You are given two different gases that are at the same conditions and you mix them in equal volumes. Determine the molar entropy of mixing, ?
What is the maximum bending moment in the beam : A hollow cylinder with outer radius r0 and inner radius ri is loaded by a uniformly distributed load q across its length L.  The beam is supported by a roller at its left end and a pin L/5 from its right end.   What is the maximum bending moment in t..
Calculate the ratio horizon : Calculate the ratio horizon for a 500-ft transmitting antenna and a receiving antenna of 20ft. Calculate the required height increase for the receiving antenna if a 10% increase in the radio horizon were required.
What was the cold war? : What was the Cold War?
Write a brief report summarizing the amounts spent : Write a brief report summarizing the amounts spent during the holidays. Be sure to include the total amount spent, and the percent spent by each group.
How tall is the building : You are looking up at a building, and the angle of elevation is 20 . If you move 100 ft further away, the angle of elevation becomes 16 . How tall is the building?
Essay describing your discernment of authenticity and virtue : Based on the readings and the video, write a 3-4 page essay describing your discernment of authenticity, virtue, and value in your current life. Connect your essay to the main ideas in at least 5 of the assigned readings

Reviews

Write a Review

Electrical Engineering Questions & Answers

  What to expect the difference in the vbe values to be

Two transistors have EBJ areas as follows: AE1 = AE1 = 400μm x 400μm and AE2 = 0.4μm x 0.2μm. If the two transistors are operated in the active mode and conduct equal collector currents

  Find the probability of e at least 1 defective directly

Three screws are drawn at random from a lot of 100 screws, 10 of which are defective. Find the probability that the screws drawn will be nondefective in drawing (a) with replacement, (b) without replacement.

  What is maximum load that can be connected to tansformer

Three single phase transformers rated at 100kVA, 13.2kV / 2.4kV are connected in wye -delta on a 3 phase, 18kV line. What is the maximum load that can be connected to the transformer bank

  Calculate the common mode rejection ratio-cmrr

A balanced transmission line picks up an undesired signal with a 5-mW level. After conversion to an unbalanced signal using a center-tapped transformer, the undesired signal is 0.011 uW. Calculate the common mode rejection ratio (CMRR).

  What will the armature voltage will be at rated load

A separately excited DC generator rated at 125V has an armature resistance of 0.75 ohms and a no load coltage of 140 VDC. What will the armature voltage will be at rated load

  Find the appropriate electrical length of the line

An open-circuited 50ohm microstrip transmission line is used in a microwave amplifier circuit to provide a capacitance of 3.2 pF at 2.3 GHz. (a) Find the appropriate electrical length of the line.

  Determine the voltage and the current across the inductor

A 10 H inductor is connected in series with a 1.0k(ohm) resistor and a switch which closes at t=0s, Determine the voltage across the inductor and the current through the inductor for t>0 if the inductor has an initial current of 10 A.

  Estimate the power rating in va for the transformer

Draw schematic for a Bridge (full-wave) peak-rectifier capable of providing de output voltage of 12V with a ±1 V ripple and a load current of 0.5A. Calculate the transformer ratio, the filter capacitor value, and the PIV for the diodes.

  Determine what is the average power of terminal

The voltage across the terminals of a certain circuit and the current entering into its (+) voltage terminal are given by: v = 4 + 12 Cos[377 t + 60 Degree] - 6 Cos[754 t - 30 Degree] i = 5 + 10 Cos[377 t + 45 Degree] + 2 Cos[754 t + 15 Degree] What ..

  What are the limits that the actual value will fall under

an analog ammeter and the faceplate states an accuracy of +/- 1.5% of full scale value. if we take a measurement on the 10A scale and we measure 1.8A, what are the limits that the actual value will fall under.

  What is the dominant current mechanism for forward applied

A silicon step junction diode with NA acceptor atoms on the p side and ND donor atoms on the n side is fabricated. The diode is not ideal. What is the dominant current mechanism for forward applied voltages close to zero

  Determine the power factor-complex power and real power

The voltage across a certain load is V = 1200√2

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd