User Account

All Pages

Calculate the radiation power of the people

Assignment Help Mechanical Engineering
Reference no: EM131122805

Someone with an external body temperature of 3 degrees Celsius present in the room at a temperature of 25 degrees Celsius. assuming the body emissivity to 0.5 and the surface area of the body as a 2.0 sq m, calculate the radiation power of the people.

Reference no: EM131122805

Questions Cloud

Is patents cannot be renewed : An auto mechanic may not collect under New York No-fault insurance for injuries sustained while repairing a vehicle at work.
Calculate the centripetal force : Calculate the centripetal force required to rotate a 3kg mass in a 6m diameter circle at one 60 revolutions per minute
Analyze the elasticity of demand for product within industry : Analyze the elasticity of demand for products within the selected industry relevant to Katrina's Candies. Determine the factors involved in making decisions about pricing these products that you believe to be the most influential.
What type of contract will he be in : Mr. Harry took an insurance cover for his house and pays $ 100 per month. In an instance of his house burning what type of contract will he be in?
Calculate the radiation power of the people : Someone with an external body temperature of 3 degrees Celsius present in the room at a temperature of 25 degrees Celsius. assuming the body emissivity to 0.5 and the surface area of the body as a 2.0 sq m, calculate the radiation power of the peo..
What is the pressure difference from one end of the pipe : A piping system consists of 300 ft of 2-in pipe, a sudden expansion to 3-in pipe and then 75 ft of 3-in pipe. Water is flowing at 125 gal/min through the system. What is the pressure difference from one end of the pipe to the other
Draw a graph of the components for an elevator-position : Draw a graph of the components for an elevator-position control
Discuss each of the directors contentions : In response, the directors argue that: (1) no illegal activity had occurred; (2) if an illegal activity did occur, it was not at a valid meeting of the corporation and was therefore not an official action of the board; and (3) if they had to legal..
Determine the normal force in bar : A pin-connected structure consists of a rigid beam ABCD and two supporting bars. Bar (1) is an aluminum alloy [E = 70 GPa] with a cross-sectional area of A1 = 2,400 mm2. determine the normal force in bar (1)

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Compute reactions of a simply supported continuous beam

Calculate reactions of a simply supported continuous beam. A beam is simply supported at the ends and is continuous over two spans.

  Determine a the rate of steam production b the rate of

hot exhaust gases leaving an internal combustion engine at 400oc and 150 kpa at a rate of 0.8 kgs is to be used to

  Determine the velocity of the air at the inlet

At steady state, air at 200 kPa, 325 K, and mass flow rate of 0.5 kg/s enters an insulated duct having differing inlet and exit cross-sectional areas. The inlet cross-sectional area is 6 cm2. At the duct exit, the pressure of the air is 100 kPa and t..

  A pipeline has been proposed to carry natural gas 1715

a pipeline has been proposed to carry natural gas 1715 miles fro alaskas north slope to calgary alberta canada. the

  Ratio of turbulent to laminar heat transfer coefficients

Water at a local bulk temperature of 24°C flows at 0.8 m/s through a smooth, 1.5-cm-ID tube that is kept at 30°C and the flow is fully developed. The system is extremely clean and quiet, and the flow stays laminar until a noisy air compressor is turn..

  Determine the velocities of the spheres immediately after

sphere a has a mass of 23 kg and a radius of 75 mm while sphere b has a mass of 4 kg and a radius of 50 mm. if the

  It is desired to redue this by a factor of 100 while

the heat input to a cold box is to be reduced by adding extruded polystyrene sheets p55kg m-3 k0.027w m-1 k-1

  Compute the work done for this process

(1) I shte cooling process polytropic? If so, what is the value of n? (2) Find the final state pressure. (3) Compute the work done for this process considering the water as a closed system.

  Five hundred cubic feet per second of water flow in a

five hundred cubic feet per second of water flow in a rectangular open channel 20 ft wide and 8 ft deep. after passing

  The inlet and outlet diametersof the nozzle are20 mm and10

superheated steam enters a nozzleat 0.13 mpaand 600 k and exits at 0.1 mpa. heat interactions and frictional effects

  The heat transfer coefficients in the inner tube and in the

5000 kghr of water will be heated from 20o c to35o c by hot water at 140oc a 15o c hot water temperature drop

  Determining the atmospheric density

A tank of volume V. is filled initially with air at atmospheric density pa,. Beginning at t = 0, a pump delivers to the tank a mixture  of air and water.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd