Calculate the pressure in the constriction in a pipe

Assignment Help Civil Engineering
Reference no: EM13317368

When 0.3 m^3/s water flows through a 150 mm constriction in a 300 mm horizontal pipeline, the pressure at a point in the pipe is 345 kPa, and the head loss between this point and the constriction is 3 m. Calculate the pressure in the constriction.

Reference no: EM13317368

Questions Cloud

Determine the work done by gravity : An 80.0 kg painter climbs a 2.45 m ladder that is at an angle of 25 degrees with a vertical wall. What is the work done by gravity as the painter climbs the ladder
What was the initial speed of the bullet : A rifle bullet of mass 8.6 g is fired into a 1.23 kg block where it becomes embedded. what was the initial speed of the bullet
Calculate what is the direction of flow for 3 cfs flow : A water pipe gradually changes from 6 in to 8 in diameter accompanied by an increase in elevation of 10 f t. If the pressure at the 6 in and 8 in sections are 9 psi and 6 psi respectively, what is the direction of flow for 3 cfs flow
What is the frequency of this system : The maximum speed of a 4 kg mass attached to a spring is 0.68 m/s, and the maximum force exerted on the mass is 12 N. What is the frequency of this system
Calculate the pressure in the constriction in a pipe : When 0.3 m^3/s water flows through a 150 mm constriction in a 300 mm horizontal pipeline, the pressure at a point in the pipe is 345 kPa, and the head loss between this point and the constriction is 3 m.
When the fire truck is at rest : A fire truck siren produces a steady single tone of frequency 500 Hz when at rest. When the fire truck is at rest
Determine flow rate into or out of each reservoir : Three reservoirs are connected by three pipes with hA = 100 f t, hB = 20 f t, hC = 0 f t, l1 = 1000 f t, l2 = 500 f t, l3 = 400 f t and D1 = D2 = D3 = 1 f t. Determine flow rate into or out of each reservoir if friction in each pipe is 0.02.
Terminate the linked list properly : Define a struct which has exactly 5 variables that, for one person, will hold the last name, the "other" names. the-year-took-office. the-yew-left-office, and a pointer. The pointer will be used to point to the next set of data. for the next perso..
Determine the reaction of the rocker b on the beam : Determine the horizontal and vertical components of reaction at the pin A and the reaction of the rocker B on the beam. a)Determine the horizontal and vertical components of reaction at the pin A

Reviews

Write a Review

Civil Engineering Questions & Answers

  Ellipse construction via foci method

Ask question ellipse construction via foci method

  Compute required weight of coarse aggregate per cubic yard

A concrete mix with a 3-inch slump, w/c ratio of 0.50, and sand with a fine- ness modulus of 2.4 contains 1700 lb/yd3 of coarse aggregate. Compute the required weight of coarse aggregate per cubic yard.

  Find average normal stress at the midsection of rod

two solid rods AB and BC are welded together at B and loaded as shown. Knowing that d1=50mm and d2=30mm, find average normal stress at the midsection of rod AB and rod BC.

  Find what is the tracks radius of curvature at the instant

A race car C is being tracked via telemetry. The on-board acclerometer records and acceleration level of -.7get+.5gen. If you know that the v at this instant is 200km/hr, what is the tracks radius of curvature at this instant

  Determine the largest load p that can be supported

A log that is 2 ft in diameter is to be cut into a rectangular section for use as a simply supported beam. The material is wood select structural grade (Douglas Fir) with a specific gravity of 0.017 lb/in3.

  Find how fast must paddle wheel rotate in that compartment

the water tempearture is 10 degree celusis. how fast must the paddle wheel rotate in that compartment to generate a G(velocity gradient) value 30 s-1

  How would friction factor and pressure change be affected

Water at 20ºC flows at a velocity of 2 m/s in a 200-mm diameter horizontal ductile-iron pipe. a) Estimate the friction factor in the pipe, and state whether the pipe is hydraulically smooth or rough

  Compute the speed of the sandbags just as it hits the ground

During a hot air balloon race one specific balloon, initially at rest, accelerate vertically upward at a constant rate of a=4.5 ft/s^2 when t0=42 s from the ground the surface, which is at an altitude above mean sea level of s0=3750 ft.

  Describe what is the natural water content of the clay

a 110 cubic centimeter volume of clay weighs 145 g in its undisturbed state. when the clay specimen is dried it weighs 110.5g. what is the natural water content of the clay, and what is the degree of saturation Assume Gs=2.70

  How to identify the sources of information presented at work

The knowledge of the geological and geotechnical characteristics of the subsoil is a basic step, fundamental to the development of any type of research, evaluation, study or project in the areas of Civil and Environmental Engineering.

  Calculate average flow rate and hydraulic gradient

The cylinder has a length of 120 cm and a diameter of 12 cm. The field sample with a porosity of 0.24 is tested under a constant head difference of 160 cm with water at 10 degree Celcius.

  Calculate what is the equation for the applied load w

The vertical deflection in a simply supported beam follows the following equation: v = -[(w_0*x)/(360LEI)](7L^4 - 10*L^2*x^2 + 3*x^4) What is the equation for the applied load w(x)

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd