Calculate the power output in kw

Assignment Help Mechanical Engineering
Reference no: EM13212312

Air enters a turbine at 40 kN/m2, 900 C, and leaves at 10 kN/m2. The flow is reversible and adiabatic. Inlet velocity is quite low and outlet velocity is 150 m/s through a cross-sectional area of 0.20 m2. Calculate the power output in kW.

Reference no: EM13212312

Questions Cloud

Determine the exit temperature : Determine (a) the exit temperature, (b) the exit relative humidity of the air, (c) the exit velocity.
Determine the expressions for the principal stresses : A circular shaft is subjected to a torque Ta and a bending moment Ma. Assuming that the diameter of the shaft is d, determine the expressions for the principal stresses and maximum shear stress in terms of Ma, Ta and d.
Determine the maximum horizontal displacement : Determine the maximum horizontal displacement s of the block. Each of the two springs has a stiffness of k = 2500N/m and an unstretched length of 0.15 m.
State what affect will adding more so3 have on the system : Consider the following reaction at equilibrium. What affect will adding more SO3 have on the system?
Calculate the power output in kw : Air enters a turbine at 40 kN/m2, 900 C, and leaves at 10 kN/m2. The flow is reversible and adiabatic. Inlet velocity is quite low and outlet velocity is 150 m/s through a cross-sectional area of 0.20 m2. Calculate the power output in kW.
Plot the moment about b : Plot the moment about B for 320mm
State the equation for an electrochemical cell reaction : Predict the immediate effect of the following changes on the observed cell voltage E.Increased E,Decreased E,No change E.
Why do thermoplastics tend to brittle in very cold weather : Why do thermoplastics tend to become brittle in very cold weather?
What determines a nations real aggregate income : what determines a nation's real aggregate income According to the classical model of income determination, what determines a nation's real aggregate income What accounts for the difference between the two models

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Explain when the discharge upstream is suddenly increased

when the discharge upstream is suddenly increased to 70 cfs/ft. What is the speed and height of the surge wave

  What is the mass of the lead weight

What is the mass of the lead weight, if 100 J of heat is lost from the water after the weight falls a distance of 3 m.

  How many times more ignition energy is required

How many times more ignition energy is required to achieve ignition of a fuel-air mixture at sea level with T = 298 K than at altitude of 6000 m where pressure P = 47,166 Pa and T = 248 K?

  What is the change of energy stored in the battery

A 12 Volt battery is charged by supplying 3 Amps over a period of 6 hours. What is the change of energy stored in the battery if the battery loses 400kJ of heat during charging.

  Calculate the friction loss in the turbine

If the efficiency of the turbine in converting the mechanical energy given up by the fluid to the turbine shaft is 89% (nt = 0.89), calculate the friction loss in the turbine in J/kg.

  Determination of the heat transfer coefficient values

this would provide you with a set of Reynolds numbers. Next, using the integral method, determine the velocity profiles within the boundary layer to be followed by determination of the heat transfer coefficient values for your selected Reynolds numbe..

  What is the natural coefficient of variation

Now suppose the mean time to failure (mf) on the expose machine is 60 hours and the repair time is exponentially distributed with a mean of 2 hours (mr). What are the effective mean and CV of the process time for a job of 60 panels?

  Explain horsepower and efficiency of three-phase motor

Horsepower and efficiency of three-phase motor, If a fully loaded 440V, three-phase motor draws 12.4 A at 86% power factor (pf). It's speed is 1730 rpm and its torque output to a mechanical load is 29.1 lb-ft x 1.356 = 39.5 Nm.

  Define the temperature of the water drops

The temperature of the water drops to 260 F as a result of heat transfer to the surroundings. Determine the final pressure in the tank?

  Create a window in java

Create a window apllication in java

  Compare and comment on the results obtained

Using the required parameters for a typical large size car* and an appropriate frontal Quarter-Car model.

  Explain what is the amplitude of the response x

In the idealized model attached shown, m = 15 kg, k = 135 N/m, and the viscous damping ratio is 0.15. Assume that an external harmonic force F(t) = 15 cos 4 t acts on the system with F0=15 N and forcing frequency of 4 rad/s.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd