Calculate the percentage of the cans that is expected to be

Assignment Help Mechanical Engineering
Reference no: EM13603075

On an assembly line that fills 8-ounce cans, a can will be rejected if its weight is less than 7.90 ounces. In a large sample, the mean and the standard deviation of the weight of a can is measured to be 8.05 and 0.05 oz, respectively. (a) Calculate the percentage of the cans that is expected to be rejected on the basis of the given criterion. (b) If the filling equipment is adjusted so that the average weight becomes 8.10 oz, but the standard deviation remains 0.05 oz, calculate the rejection rate (% of cans being rejected). (c) If the filling equipment is adjusted so that the average weight remains 8.05 oz, but the standard deviation is reduced to 0.03 oz, calculate the rejection rate.

Reference no: EM13603075

Questions Cloud

Question what are the directions of electric and magnetic : question what are the directions of electric and magnetic field vectors relative to each other and relative to the
The surfaces air temperature is 15 degree c a parcel of air : the atmosphere is stable with a lapse rate of -0.2 degree c100 m. the surfaces air temperature is 15 degree c. a parcel
Mystic inc uses a job order costing system and applies : mystic inc. uses a job order costing system and applies overhead to jobs at a predetermined rate of 4.25 per direct
Rovniak reeds a manufacturer of saxophone oboe and clarinet : rovniak reeds a manufacturer of saxophone oboe and clarinet reeds has projected sales to be 890000 in october 950000
Calculate the percentage of the cans that is expected to be : on an assembly line that fills 8-ounce cans a can will be rejected if its weight is less than 7.90 ounces. in a large
The weight of an organ in adult males has a bell shaped : the weight of an organ in adult males has a bell shaped distribution with a mean of 310 grams and a standard deviation
Is the direction of the electric force acting on the 205-nc : 1. a 2.05-nc point charge is 3.61 cm away from a -3.04-nc point charge. what is the magnitude of the electric force
On his sport team the mean height is 71 in and the standard : on his sport team the mean height is 71 in and the standard deviation is 3 in.jeffs height is 76 in.in his sport team
Regal products has a budget of 900000 in 20x3 for : regal products has a budget of 900000 in 20x3 for prevention costs. if it decides to automate a portion of its

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the acceleration of the cabinet

Determine the acceleration of the cabinet when sA = 40 ft. Note that when sB = 0, sA = 0 (points A and B are coincident).

  Explain what will the ratio of the angle of twist

What will the ratio of the angle of twist be to that of the hollow shaft if the maximum shear stress in the material of 75 N / mm ^2 and what is the ratio of actual permissible shear stress?

  Find the speed of the block

Assuming the pulley is a uniform disk with a mass of 0.31 {rm kg}, find the speed of the block after it has fallen through a height of 0.50 {rm m}.

  A cylindrical bar of radius 15 mm and length 100 mm is held

a cylindrical bar of radius 15 mm and length 100 mm is held at both ends. if at 30 degc no axial force exists in the

  Determine the rate of heat transfer to the mid-stage

Determine the rate of heat transfer to the mid-stage cold head and determine the rate of heat transfer to the cold head

  The robotrsquosnbspcontrol memory has a 10 bit capacity it

one axis of a rrl robot is a linear slide with a total range of 950mm. the robotrsquosnbspcontrol memory has a 10 bit

  The gap between them is filled with molten polymer

Two flat, rectangular plates with a lateral dimension w*l lie parallel, one above the other, a distance h apart. The gap between them is filled with molten polymer.

  If the length and diameter are measured at four different

the volume of a cylinder is to be determined from measurements of the diameter and length. if the length and diameter

  A preheater involves the use of condensing steam at 100 on

a preheater involves the use of condensing steam at 100? on the inside of a bank of tubes to heat air that enters at 1

  A solid object of aisi 302 steel at a temperature of 850c

a solid object of aisi 302 steel at a temperature of 850?c is quenched in mineral oil at a temperature of 25?c. the oil

  Determine the velocity of the airplane required for pilot

Determine the velocity of the airplane required for pilot to experience weightlessness at the top of the circular path.

  Plot the lift and drag forces exerted on an airfoil

Plot the lift and drag forces exerted on an airfoil as a function of velocity. Use velocity values going from 0 to 45 m/s on a log-linear plot (log-scale on the y axis).

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd