Calculate the percent transmittance of the sample solution

Assignment Help Mechanical Engineering
Reference no: EM131083734

A portable photometer with a linear response to radiation registered 63.8 μA with the solvent in the light path. The photometer was set to zero with no light striking the detector. Replacement of the solvent with an absorbing solution yielded a response of 41.6 μA. Calculate

(a) The percent transmittance of the sample solution.

(b) The absorbance of the sample solution.

(c) The transmittance to be expected for a solution in which the concentration of the absorber is one third that of the original sample solution.

(d) The transmittance to be expected for a solution that has twice the concentration of the sample solution.

Reference no: EM131083734

Questions Cloud

Describe the differences between the following : Describe the differences between the following and list any particular advantages possessed by one over the other.
About international strategies-diversification strategies : Are international strategies always just a special case of diversification strategies that a firm might pursue? What, if anything, is different about international strategies and diversification strategies?
Write discussion about the article on the homours : Write discussions about the articles "On The Homours" and "On The Powers of Foods". Analyzed issue using the reading?. Used standard, correct grammar, punctuation and spelling, for the most part??.
State select on the basis of annual worth analysis : A state highway department is trying to decide whether it should “hot-patch” a short section of an existing county road or resurface it. If the hot-patch method is used, approximately 300 cubic meters of material would be required at a cost of $700 p..
Calculate the percent transmittance of the sample solution : The percent transmittance of the sample solution.
How to swim freestyle while keeping their hips raised : Swim coach Rob teaches athletes how to swim freestyle while keeping their hips raised. Let q represent the number of swimmers that learn the technique, and let h represent the number of hours of individual training Rob provides in which the swimmers ..
The two products are partial substitutes : Consider two manufacturers, Each makes a product. The two products are partial substitutes. Priced at p_t, product i receives a demand q_1 = 15 - 2 p_1 + p_2 and q_2 = 15 - 2 p_2 + p_1. It costs $5 to produce a unit of product 1 and $10 to produce a ..
Suppose the brownian motion process : Suppose the Brownian motion process is constrained by barriers. That is, we wish to generate a process Y(t) such that -b ≤ Y(t) ≤ b for a constant b > 0. Build a simulation of this system. Estimate P[Y(t) = b]
Using sylow theorem solve given problem : Math 171: Abstract Algebra, Fall 2014- Assignment 7. In this problem we prove the first part of the Sylow Theorem. Suppose G is a group and |G| = pkm with gcd(p, m) = 1. We will prove G has a subgroup of order pk

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What is the friction factor of the duct

A 50 x 50 cm duct is 10 m in length. Nitrogen enters at M1 = 3.0 and leaves at M2 = 1.7, with T2 = 280 K and P2 = 7 x 104 N/m2. Find the static and stagnation conditions at the entrance.

  Ratio between longitudinal and lateral deformations

At the proportional limit, a 30 mm wide × 12 mm thick bar elongates 2.0 mm under an axial load of 41.5 kN. The bar is 1.5-m long. If Poisson’s ratio (ratio between longitudinal and lateral deformations) is 0.33 for the material, determine:

  What is the heat transfer that must occur to maintain

A 3in diameter can which is 6in tall contains R134a at 70oF. Initially the can is half full, by volume, of liquid R134a. The can is connected to and air conditioning system and is used to fill up that system. Knowing only vapor R134a leaves the conta..

  A cylindrical specimen of an aluminum alloy has a youngs

a cylindrical specimen of an aluminum alloy has a youngs modulus of 59gpa original length of 250mm length at fracture

  What are the engineering strain and true strain

What is the yield strength and ultimate tensile strength of the material. What are the engineering strain and true strain when the specimen is elongated to 0.2 inches

  Hot air is contained in a vertical frictionless

hot air is contained in a vertical frictionless piston-cylinder device.the piston has a mass of 4 kg and a

  Cn the final equilibrium state be determined how many

consider a rigid tank with a partition such that there are two equal volumes which are known. on one side has water at

  Determine the silicon temperature and the electric power

consider the photovoltaic solar panel of example 3.3. the heat transfer coefficient should no longer be takento be a

  Consider steady flow of a constant property fluid in a long

consider steady flow of a constant property fluid in a long duct formed by two parallel planes. consider a point

  Car a is speeding in the positive x direction and is about

car a is speeding in the positive x direction and is about to run through a red light and collide with car b heading

  A 3 cm thick stainless steel thermal diffusivity 00000044

a 3 cm thick stainless steel thermal diffusivity 0.0000044 k16.3 plate initially at 500degc is suddenly exposed to

  Calculate maximum velocity

A 100 kg body falls from rest from a height of 100 m above the ground. Calculate its maximum velocity when it hits the ground. (a) Use the maximum value for gravity, (b) use the minimum value for gravity, and (c) use the standard value for gravity.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd