User Account

All Pages

Calculate the outlet temperature

Assignment Help Mechanical Engineering
Reference no: EM13212711

A compressor operating adiabatically is to compress 2.83 m^3/min of air at 29.4C and 102.7 kN/m^2 to 311.6kN/m^2. Calculate the power required if the efficiency of the compressor is 75%. Also, calculate the outlet temperature.

Reference no: EM13212711

Questions Cloud

What is the npv of all cash flows to ocean carriers : What is the NPV of all cash flows to Ocean Carriers if it decides to sell the carrier when it is 15 years old?
What are the potential weaknesses of the model : The forecasting staff for the Prizer Corporation has developed a model to predict sales of its air-cushioned-ride snowmobiles. The model specifies that sales S vary jointly with disposable personal income Y and the population between ages 15 and 4..
Determine the power : A commercial heat pump has energy in to the system at a rate of 60 kW from a thermal reservoir. If the power input from an electric motor is 15 kW, (a) determine the power (kW) delivered to the office area. (b) Determine the coefficient of perform..
What is the best point estimate of the population mean : Recently, a university surveyed recent graduates of the English Department for their starting salaries. Four hundred graduates returned the survey. The average salary was $25,000 with a standard deviation of $2,500. What is the best point estimate..
Calculate the outlet temperature : A compressor operating adiabatically is to compress 2.83 m^3/min of air at 29.4C and 102.7 kN/m^2 to 311.6kN/m^2. Calculate the power required if the efficiency of the compressor is 75%. Also, calculate the outlet temperature.
What is the present worth for each scenario : A project has a life of 10 years, and no salvage value. The firm uses an interst rate of 12% to evaluate engineering projects. The project has an uncertain first cost and net revenue. First Cost P Net Revenue P -- $300,000 0.2 $70,000 0.3 400,000 ..
How long is required for half the ice cube to melt : how long is required for half the ice cube to melt? State clearly all the assumptions you make in formulating your model of this problem.
What is the rate of heat loss to the ambient : The external heat transfer coefficient is h=10 W/m^2*K. What is the rate of heat loss to the ambient?
How deep is the notch : A block of metal has a 90 notch cut from its lower surface. The notched part rests on a circular cylinder of diameter 2.0 cm, as shown in Fig. 4.15. If the lower surface of the par is 1.3 cm above the base plane, how deep is the notch?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Calculate the magnitude of the moment

Calculate the magnitude of the moment about the base point O of the 600 N force and calculate and draw the shear force and bending moment diagram for the cantilever beam

  Determine the energy change if the system mass

For the process where q= 62.5 kj/kg and wkcs= 60 kj/kg determine the energy change if the system mass is 2 kg.

  Determine the stresses in polar co-ordinate system

Show that Airy's stress function ? = Crθ sinθ satisfies the biharmonic equation. Also determine the stresses in polar co-ordinate system.

  Determine fourier number compare two identical steel spheres

Determine Fourier Number, Compare two identical steel spheres, except the first has a two inch diameter while the second sphere has a four inch diameter. The larger sphere will have a Fourier number approximately

  Calculate the heat transfer and the work done

Saturated water vapor at 200oC is isothermally condensed to a saturated liquid in a piston-cylinder device. Calculate the heat transfer and the work done during this process in kJ/kg.

  Hydrostatic relation an empirical formula relating

Hydrostatic relation, An empirical formula relating pressure and density for seawater w/ temperature held constant is

  Overlay the frequency spectrum of the excitation

Sketch the frequency response of the system. Overlay the frequency spectrum of the excitation and as you start the system up, increasing Ω from 0 to 60 rpm, what speeds are most likely to excite large amplitude response? Why?

  Refrigerant leaves the evaporator as saturated vapor

Refrigerant 134a leaves the evaporator as saturated vapor at 1.4bar and is heated at constant pressure to 20 degrees C before entering the compressor.

  What is the reason for the change in enthalpy

what is the reason for the change in enthalpy between the throttle valve and the evaporator in a practical refrigeration cycle that is using R12 refrigerant.

  Explain temperature effect on materials

Temperature Effect on Materials (i) A hollow cylinder of aluminium 1 m long with a 40 mm outside diameter is at a temperature of 20 °C. What is the change in length and circumference of the cylinder when it is cooled to â?'25 °C

  Estimate the torque required at the base of a flag pole

Estimate the torque required at the base of a flag pole to hold it in place in a 30mph wind. Assume the flag pole is a vertical cylinder with D=10cm and L=10m, and assume the wind drag force is uniform along the pole.

  By what factor dose the volume change

an ideal monoatomic gas is allowed to expand slowly untill its presssure is reduce to exactly half its original value. by what factor dose the volume change if the process is adiabatic.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd