Reference no: EM13839191
Vehicle Power-Train Technologies
Engine modelling assignment:
The pressure increment dP due to combustion and piston work was derived in class for an ideal engine cycle with a finite period of heat release. This can be used to determine the pressure-time history of the engine and consequently, the cycle work done and thermal efficiency. Use any numerical method you prefer (e.g., spreadsheet, Mathcad, C++ etc.) to solve the equation and estimate the engine performance. For this analysis, use the Wiebe function shown in class to model the mass-burned fraction as a function of crank angle. Use the following assumptions:
A compression ratio CR of 10:1
A single cylinder engine with displacement of 500 cc
The combustion being modelled is of a stoichiometric mix of octane and air; 14.7 kg air to every 1 kg of air
The pressure and temperature at the start of compression is 101325 Pa and 20o C respectively
A specific heat ratio of 1.3 can be used for compression and expansion
The engine is operating at wide open throttle (WOT) with no pumping losses
The pressure and temperature in the cylinder drops instantly to pre-compression conditions at the end of the stroke at bottom dead centre (BDC)
PART A
Run your calculations for a range of combustion start times ?? from -60o to +30o and for the following burn duration angles?: 30o, 60o, 90o, 120o
Hint: solve the differential equation numerically using crank-angle increments that are small enough.
Plot a P-V diagram for the case of ?? = -30o and ?? = 90o and compare to the ideal Otto cycle diagram. Please show the start point and end point of combustion in the diagram. There is no need to plot the exhaust and intake strokes.
Calculate the net work done per cycle for each case and then plot the thermal efficiency against? on the same plot for each the four values of? Explain why there is an optimum? for each burn duration case. Based on your data, state a rule of thumb for setting the optimum?
PART B
Using equations 9.60 and 9.62 in Heywood`s text (which are explained in class) and your estimates of the pressure and temperature histories of the unburnt charge in the engine, estimate the CR needed to just cause knock for a given fuel Octane Number (ON) as defined in equation 9.62.
Hint: the onset of knock occurs when autoignition takes place just before all the fuel-air charge is burnt in an engine cycle. The integral in equation 9.60 becomes 1 at that point. Change your CR by changing the clearance volume only.
Plot this critical compression ratio CCR against ON for the following ON values: 65, 75, 85, 95, 105, 115, 125. Place the ON values on the horizontal axis. Use ?? = 90o and the corresponding ?? for maximum thermal efficiency.
How does the graph in III change if ?? = 30o instead of 90o? Explain your findings. How does the graph in III change if the start of combustion occurs well before the optimum value for ??? Explain your findings.
Please work in pairs. One student does part A and the other does part B. On the cover page of your report, please name the person who worked on part A and the person who worked on part B. Provide student numbers as well.
Please write a proper and concise report (around 15 pages in total) including introduction with aims, method, discussion and conclusion. Please do not state in your objectives that you want to learn things as this is obvious.
|
Gap inc-team assignment
: The company Gap Inc. is working with the simple ambition to "do more than sell clothes." This promise contently to guide the commitment of the company towards its communities it works and live and direct its endeavors so that it will augment its s..
|
|
Human resources office-staffing division
: Inventory: All the money the system invests in things it intends to sell, including facilities and equipment, which are likely to be sold off as scrap after they obsolesce beyond their useful lives.
|
|
Describe how heat is transferred in food preparation
: How do these cooking methods vary in relation to speed of cooking and general health. Describe how heat is transferred or dispersed in food preparation. Explain each, providing examples of cooking methods within your response.
|
|
Proportion of major corporations outsource
: A large proportion of major corporations outsource their IT functions to specialist suppliers of IT services such as IBM, EDS (now owned by Hewlett-Packard), Accenture, and Cap Gemini. What transaction costs are incurred by these outsourcing arran..
|
|
Calculate the net work done per cycle for each case
: Calculate the net work done per cycle for each case and then plot the thermal efficiency against? on the same plot for each the four values of? Explain why there is an optimum?
|
|
Consider the current situation and prevailing political
: Consider the current situation and prevailing political and economic conditions in Brazil, a BRIC country. As a manager who has been considering investment in Rio de Janeiro, how do you assess the political and economic risks at this time?
|
|
Business plan-type of business
: The type of business I would like to start is selling ornaments and trendy jewelry products. This business is important because it has many potential customers, especially the youth who mostly identify with such products. The specific products inc..
|
|
Research the codes of conduct of a large company
: Research the codes of conduct of a large company, such as Microsoft, and a small company in your local community and compare the issues that they cover. Describe the commonalities and differences of content in the codes. Discuss why you think there a..
|
|
What price should the annual payment bond sell
: Kebt Corporation's Class Semi bonds have a 12 year maturity and an 8.75% coupon paid semiannually (4.375% each 6 months), and those bonds sell at their $1,000 par value. The firm's Class Ann bonds have the same risk, maturity, nominal interest rate, ..
|