Reference no: EM13242400
1. An aluminium rod is to withstand an applied force of 200 kN. To ensure a sufficient factor of safety, the maximum allowable stress on the rod is limited to 170 MPa (170MN/m2) with a strain of 0.0025mm.mm-1. The rod must be at least 3.8 m long but must deform elastically no more than 6 mm when the force is applied. Design an appropriate rod.
2. From stress-strain diagram below for Aluminium alloy, calculate the E, YS (σY) and UTS (σU), and percent elongation at failure.
3. A 10-mm diameter rod of carbon steel is subjected to a tensile load of 50,000 N, taking beyond its yield point (YS = 600 MPa and UTS = 750 MPa). Calculate the elastic recovery that would occur upon removal of the tensile load. E = 200 x 103MPa.
4. Table 1 below shows the results of a tensile test of a 12.5 mm diameter aluminium alloy test bar with original cross sectional area Ao = 122.7 mm2)
a. Convert the load-gauge length data in Table 1 to engineering stress and strain and plot a stress-strain curve
b. From the data in Table 1, calculate the modulus of elasticity of the aluminium alloy. Use the modulus to determine the length of a 1.25 m bar to which a stress of 210 MPa is applied.
c. Compare engineering stress and strain with true stress and strain for the aluminium alloy (on a - above), and determine the (i) maximum load and (ii) fracture. The diameter at maximum load is 12.3 mm and fracture is 9.85 mm.
|
Calculate the final potential difference across the plates
: Two capacitors C1 = 3.2 ?F, C2 = 13.5 ?F are charged individually to V1 = 19.0 V, V2 = 5.6 V. Calculate the final potential difference across the plates of the capacitors once they are connected
|
|
Why innovation is at heart of creating advanatage
: Explain in one or two paragraphs why innovation is at the heart of creating and sustaining competitive advantage for firms. You need to mention the interrelationships between innovation and productivity
|
|
Calculate the pressure due to the ocean
: The greatest ocean depths on earth are found in the Marianas Trench near the Philippines, where the depth of the bottom of the trench is about 11.0 km. Calculate the pressure due to the ocean at a depth of 9.5 km
|
|
How much additional charge will flow from the battery
: A parallel-plate air capacitor of area A= 10.0 cm2 and plate separation d= 3.20 mm is charged by a battery to a voltage 50.0 V, how much additional charge will flow from the battery onto the positive plate
|
|
Calculate the modulus of elasticity
: Calculate the modulus of elasticity of the aluminium alloy. Use the modulus to determine the length of a 1.25 m bar to which a stress of 210 MPa is applied.
|
|
What speed must the golfer hit the ball
: A seasoned mini golfer is trying to make par on a tricky hole #5, at what speed must the golfer hit the ball to land the ball in the hole
|
|
Calculate the speed of the proton
: A particle with a charge of -60.0 nC is placed at the center of a nonconducting spherical shell of inner radius 20.0 cm and outer radius 24.0 cm, Calculate the speed of the proton
|
|
Find the magnitude and direction of the magnetic field
: Two long, straight wires are parallel and are separated by a distance of d = 0.230 m, The top wire in the sketch carries current I1 = 3.80 A, toward the right, and the bottom wire carries current I2 = 7.00 A, what are the magnitude and direction of t..
|
|
How many electrons would have to be placed on the sphere
: How many electrons would have to be placed on the sphere to produce an electric field of magnitude 1.41 105 N/C at a point 8.60 cm from the center of the sphere
|