Calculate the minimum number of plates using a total

Assignment Help Civil Engineering
Reference no: EM13559264

(a)A continuous distillation column containing plates is required to distil a 46% w/w ethanol (C2H5OH) in water solution. The overhead product must contain 91 % w/w ethanol and the bottom product 5 % w/w ethanol.

(b) Using the VLE diagram provided (figure 1, please attach to answer book), calculate the minimum reflux ratio required with a feed at its boiling point.

(c) Using a reflux ratio of twice the minimum reflux, calculate the minimum number of plates using a total condenser and reboiler and a Murphree plate efficiency of 65%.

(d) Under the same column conditions what is the minimum number of plates when the feed enters as a saturated vapour? Atomic weights: Carbon=12 Hydrogen=1 Oxygen =16

Reference no: EM13559264

Questions Cloud

Determine the uniform depth in the channel : A clean-earth channel, for which n=0.020, is 6m wide and lies on a slope of 0.005236. Water flows at 30m3/s through the channel and enters a reservoir. The water depth in the channel, just before the entry to reservoir, is 3m.
Determine the speed of the cubic block down the plane when : Determine the speed of the cubic block down the plane when in equilibrium.Hence determine the total force required to pull the cubic block up the plane at the same speed.
Simplify the shape of the base and the 4 legs and estimate : The Statfjord B drilling platform, was built in Norway and towed 370km in 5 days to its present site in the North Sea in August 1981. It is the heaviest object ever moved by man
Evaluate by how much does its volume decrease : The deepest place in all the oceans is the Marianas Trench, wherethe depth is 10.9 km and the pressure is 1.10E+8 Pa, by how much does its volume decrease
Calculate the minimum number of plates using a total : Using a reflux ratio of twice the minimum reflux, calculate the minimum number of plates using a total condenser and reboiler and a Murphree plate efficiency of 65%.
Equilibrium partial pressure of benzene in gas : Benzene is to be absorbed from coal gas by means of a wash oil. The inlet gas contains 3% by volume of benzene, and the exit gas should not contain more than 0.02% benzene by volume. The suggested oil circulation rate is 5 kg oil per 1m3 of inlet gas..
Find what is the specific heat of the unknown sample : A 100-g aluminum calorimeter contains 250-g of water. Twosubstances are in thermal equilibrium at 10 degrees celcius. Determine the specific heat of the unknown sample
Calculate the number of theoretical stages required : It is proposed to reduce the concentration acetaldehyde in aqueous solution from 55% to 5% by mass, by extraction with solvent S at 293K. If a counter current multiple contactor process is adopted and 0.025 kg/s of solution are treated with an equal ..
How many tubes will the calandria require to concentrate : The specific heat of the solution can be assumed to be constant at 4.18 kJ kg-1 K. The latent heat of evaporation is 2270 kJ kg-1 for the feed and steam, the boiling point rise is 15 K. The feed temperature is 303 K.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Draw the influence line for the shear at point b

Draw the influence line for the shear at point B. Plot numerical values every 5 ft. Assume the support at A is a roller and C is fixed. EI is constant.

  How many tickets are given out on a particular day

The number of parking tickets issued in a certain city on any given weekday has a Poisson distribution with parameter  = 50. What is the approximate probability that 1 between 35 and 70 tickets are given out on a particular day

  Determine who is at fault for the component failure

manufacturing process that unintentionally introduces cracks to the surface of a part was used to produce load-bearing components. The design requires that the component be able to withstand a stress of 450 MPa.

  How is copper extracted from copper suflide ore concentrates

(a) What are some of the important properties of unalloyed copper that make it an important industrial material (b) How is copper extracted from copper suflide ore concentrates

  What direction should the boat have been headed to actually

To cross a river that is 1 km wide, with a current of 6km/h, a novice boatskipper holds the bow of the boat perpindicularto the far river bank, intending to cross to a point directly across the river from the launch point.

  Engine suspended from a spreader beam

The 3.5-Mg engine is suspended from a spreader beam having a negligible mass and is hoisted by a crane which exerts a force of 40 kN on the hoisting cable. Determine the distance the engine is hoisted in 2.4 s, starting from rest.

  Determine remaining load carrying capacity of cracked beam

a reinforced concrete beam with a section of 12 inches width and 24 inches depth is reinforced with 3no. 9 bars. fc'=5000psi and fy=60000psi. a 2 inch cover is used and the beam has a simply supported span lenght of 15ft.

  Determine the final velocity of the carrier

A 30 g bullet is fired with a horizontal velocity of 450 m/s through 3-kg block B and becomes embedded in carrier C which has a mass of 30 kg. After the impact, block B slides 0.3m on C before coming to rest relative to the carrier.

  Find the required column reinforcement

A rectangular column of size 16” x 16” is to be designed for the following loads. Service D.L = 150 kips ft, Service LL = 200 kips-ft. DL Moment = 80 ft- kips, LL Moment =130 ft kips. Find the required column reinforcement.

  Find drag force fd on golf ball assuming to smooth sphere

Determine the drag force FD on a golf ball assuming it is a smooth sphere. (Assume the air is at 60 F and standard pressure.) Now determine the drag force on an actual golf ball assuming CD = 0.25. How do the two forces compare

  Determine the maximum allowable axial tensile force

A 4-cm- diameter rod of aluminum 7075-T6 is to subjected to an axial tensile force such that the factor of safety based on the yield stress on 1.75. Find the maximum allowable tensile force.

  Calculate the overflow rate detention time and weir loading

A fine sand has a hydraulic condutivity of 3.5 x 10^-5 m/s a hydraulic gradient of 0.00141, and a porosity of 45 percent. Detrmine the Darcy velocity and the averge linear velocity

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd