Calculate the mass of fuel injected per cylinder

Assignment Help Mechanical Engineering
Reference no: EM13707420

A direct injection, four-stroke, six cylinder Diesel engine has 10L if displacement volume. Bore and stroke dimensions are 125mm and 136mm, respectively. The engine was designed to deliver 184 HP at 2100 RPM. Calculate the air flow rate (g/s) when piston speed is 8 m/s and volumetric efficiency is 92%. Calculate the mass of fuel injected per cylinder, per cycle (mg).

Reference no: EM13707420

Questions Cloud

Determine the maximum shear stress at the point : The stresses at a point in plane stress on a sheet metal roof were found to be sigma_xx = 10 ksi (C), sigma_yy = 20 ksi (C) and Tau_xy = 30 ksi using matrix methods a) determine the normal and shear stresses on a plane passing through the point that ..
Determine the design thrust for a throat area : A rocket nozzle has a chamber pressure of 20 Bar (2 MPa) and a chamber temperature of 2750 K. The rocket is designed to operate isentropically at 12,500 m altitude. Note that the pressure at 12,500 m can be estimated using this equation P/P0 = exp [-..
Determine internal pressure required to initiate yielding : A thin-walled cylindrical pressure vessel is capped at the end and is subjected to an internal pressure (p). The inside diameter of the vessel is 6 ft and the wall thickness is 1.5 inch. The vessel is made of steel with tensile yield strength and com..
Calculate indicated mean effective pressure : A 3L, 4-stroke, V6 engine with a 9.5:1 compression ratio delivers 205 N-m at 3600 RPM. At this speed, air enters the cylinder at 85 kPa and 60 C and combustion ends at 20 crank angle after top-dead-center. It is known that the engine is square and th..
Calculate the mass of fuel injected per cylinder : A direct injection, four-stroke, six cylinder Diesel engine has 10L if displacement volume. Bore and stroke dimensions are 125mm and 136mm, respectively. The engine was designed to deliver 184 HP at 2100 RPM. Calculate the air flow rate (g/s) when pi..
What final fraction of the glasss volume is filled with air : An empty drinking glass is held upside down just above the surface of water. A scuba diver carefully takes the glass, which remains upside down, to a depth of 10.3 meters below the surface so that a sample of air is trapped in the glass. Assume that ..
Similarity and difference between trip and twip steels : Discuss the similarity and difference between TRIP and TWIP steels. Discuss the advantages of TWIP steels. Discuss the effects/roles of Mn, Al and Si in TWIP steels.
Various car and truck spare parts using different steels : Suppose you are appointed as a material engineer at an industry company. The company produces, cutting tools, various car and truck spare parts using different steels. The steels as raw materials to make the parts. All steels are round bars with 50 m..
Thin-walled cylindrical pressure vessel : A thin-walled cylindrical pressure vessel is capped at the end and is subjected to an internal pressure (p). The inside diameter of the vessel is 6 ft and the wall thickness is 1.5 inch. The vessel is made of steel with tensile yield strength and com..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd