Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
1.Water is flowing in a 6-cm diameter pipe at 20 m/s at 10?C. If the pipe enlarges to a diameter of 12-cm, calculate the reduced velocity. Also, calculate the mass flux rate and the flow rate.
2.A rectangular gate is inclined at an angle of 30 degrees from the horizontal. It is 4 ft wide by 6 feet long. If it is hung from its upper end which is 8 feet below the waters top edge, what minimum applied force (bottom) is needed to open the gate?
3.The blades of the portable fan generate a 1 lb thrust T as shown. (h = 8 in.) Compute the moment MO of this force about the rear support point O. For comparison, determine the moment about O due to the weight of the motor-fan unit AB, whose weight of 12 lb acts at G.
4.During a drilling operation, the small robotic device is subjected to an (F =) 900 N force at point C as shown. (? = 25°.) Replace this force by an equivalent force-couple system at point O.
aluminum foil used to package food is approximately 0.001 inch thick. assume that all of the unit cells of the aluminum are arranged so that a is perpendicular to the foil surface.
what are the three meterials based on the predominant types of bond and what are the predominant types of bond in each category
Determine the operating speeds of the machine at which the machine's steady-state amplitude is less than 0.2 mm. Take keq = 3 EI/L3.
Consider your cooking gas contains 80% propane and 20% butane. While burning on a cooktop, assume it burns with 200% excess air. If no heat is lost, determine the maximum possible flame temperature.
Calculate the diameter and depth of a circular sedimentation basin for a design flow of 3800 m3/day based on an overflow rate of 0.00024 m/s and a detention time of 3 hr.
A rinsed and dried filter weighed 0.3588 grams before the sample was filtered and then weighed 0.3630 grams after the sample was filtered and being at dried at 103C. What is the TSS for this sample
During frequent braking under race conditions the disk brake rotors on the car described above reach a temperature of 500C. These disk brakes rely on forced convection to cool them. The dimensions of each disk rotor are: outer radius 130mm
The 2 Mg car is being towed by a winch. If the winch exerts a force of T=105s on the cable, where 14m is the displacement of the car in meters, determine the speed of the car when s , starting from rest. Neglect rolling resistance of the car.
A batch system is assumed to be first order. The initial concentration is 225 mg/L. If the reaction rate constant is 0.65 hr^-1, how long will it take for the concentration to be one-quarter the starting concentration
In polluted areas of Texas, registered vehicles must undergo an annual emissions inspection. In Fort Bend County (near Houston), 27 vehicles failed the emissions test.
The pump graphs are given to us, and I'm asked to determine possible lengths and diameters of the pipe to meet two requirments. The system can have multiple outputs in order to satisfy the needs, but they must be occuring at the same time.
Find the maximum bending stresses(wood) and (steel), in the wood and steel, respectively, due to the uniform load if the modulus of elasticity are E (wood)=10 GPa for the wood and E (s)=210 GPa for the steel.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd