Calculate the mass flow rate of steam

Assignment Help Mechanical Engineering
Reference no: EM13717625

A steam power generation plant produces 200mw of power. Steam leaves the dealer at 150 bar and 650°c. After expansion through the first stage turbine to a pressure of 40 bar, 15% of the steam is extracted to feed the water heater. The remaining steam is heated to 650°c then expanded to a condenser pressure of 0.04 bar through a second turbine stag. It is assumed that the actual cycle will have an efficiency of 70% and the generator mechanical and electrical efficiency is 95%. Calculate the mass flow rate of steam in kg/hr. The steam rate.

Reference no: EM13717625

Questions Cloud

Determine rate of heat rejection to environment in mw : A steam power plant with a power output of 160 MW consumes coal at a rate of 62 metric tons per hour. If the heating value of the coal is 29900 kJ/kg, determine the overall efficiency of the plant.
How far up the incline will they go : A 16 lb bowling ball is rolled at a speed of 12 ft/sec toward a 10 lb sled that sits on a 45o in-cline. Once it hits the sled, it rolls up the incline inside of it. How far up the incline will they go?
Liabilities have changed from the day before : Suppose the assets of the Silver Lode Bank are $100,000 higher than on the previous day and its net worth is up $40,000. By how much and in what direction must its liabilities have changed from the day before?
Calculate the final temperature and heat transfer : Argon is compressed in a polytropic process with n=1.2 from 120 kPa (P1) and 10 °C (T1) to 800 kPa (P2) in a piston-cylinder device. List all the assumptions. Derive the equation of the boundary work (kJ/kg) in terms of P1, T1, & P1. It should includ..
Calculate the mass flow rate of steam : A steam power generation plant produces 200mw of power. Steam leaves the dealer at 150 bar and 650°c. After expansion through the first stage turbine to a pressure of 40 bar, 15% of the steam is extracted to feed the water heater. The remaining steam..
Police officers may have in intervening in domestic violence : 3. What do you think are some of the challenges (personal as well as professional) that Police Officers may have in intervening in domestic violence episodes.
What is the appropriate tunnel pressure in atm : An airplane, of overall length 55ft, is designed to fly at 680m/s at 8000-m standard altitude. A one-thirtieth-scale model is to be tested in a pressurized helium wind tunnel at 20 degrees Celsius. What is the appropriate tunnel pressure in atm? Even..
Determine the outlet density of the steam : Saturated liquid steam at 2 MPa steadily enters a valve where it is throttled to 0.3 MPa. The inlet and outlet diameter is 1 cm. The flow rate is 0.012 kg/s. Determine the outlet density [kg/m3] of the steam. Also show that it is reasonable to neglec..
Adverse effects of sweatshop labor practices : From the e-Activity, determine at least three (3) ways in which United States' businesses can address the adverse effects of sweatshop labor practices. Provide one (1) specific example of each way that you have just determined to support your ..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  At a surface cutting speed of 190 mmin the productive tool

at a surface cutting speed of 190 mmin the productive tool life was 60 minutes. at a surface cutting speed of 225 mmin

  A package is dropped from the plane which is flying with a

a package is dropped from the plane which is flying with a constant horizontal velocity of va 160 fts at a height h

  A disk has a mass of 4kg and a radius of 90mm it is at rest

a disk has a mass of 4kg and a radius of 90mm it is at rest when it is placed in contact with the belt which moves with

  Determine the pressure of the water

determine the pressure of the water after the partition has been remived and enough heat has been transferred so that the temperature of the water is 3(degrees)C.

  Find the turbine isentropic efficiency

Find the turbine's (b) isentropic efficiency (%), (c) reversible work (kJ/kg), (d) irreversibility(kJ/kg), and (e) exergy destruction (kJ/kg). (f) Draw a T-s diagram of the process

  Necessary thermodynamic calculations

Model a cup of coffee as a closed system containing 1 lbm of pure water at constant pressure of 14.7 psia. Using your knowledge of the 2nd Law, prove that it would be impossible for coffee at room temperature of 70 °F to heat up to 120 °F by receivin..

  Standard machining parameter formulae for milling

Using the standard machining parameter formulae for milling, determine the speed (rpm), feed (ipm) and machining time (TM) recommended to horizontal mill ANSI #1018 cold rolled steel that is 1.50 inch long with a 10 tooth 4.0 inch diameter slab mill ..

  A 50-lb sphere with a radius of qyration of 04 ft is

a 50-lb sphere with a radius of qyration of 0.4 ft is accelerated about its centroidal axis. determine the torque

  If the combustion is complete and the exit temperature of

liquid propane c3h8 enters a combustion chamber at 25 c at a rate of 1.2 kgmin where it is mixed and burned with 150

  What is the new exit pressure and mach number

A constant-area duct is fed by a converging-only nozzle. The nozzle receives air from a large chamber at p1=600 KPa and T1=550 K. The duct has a friction length of 5.3, and it is choked at the exit. What is the pressure at the end of the duct? If 80 ..

  Explain the compression ratio of an air-standard otto cycle

The compression ratio of an air-standard Otto cycle is 9.5. Prior to the isentropic compression process, the air is at 100 kPa, 17 C, and 600 cm2

  An axial flow compressor stage has blade rootmean and tip

an axial flow compressor stage has blade rootmean and tip velocities of 150200 and 250 ms. the stage is to be designed

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd