Calculate the lowest tm mode possible

Assignment Help Mechanical Engineering
Reference no: EM131213205

Application: TE/TM waves in strip lines. A parallel plate waveguide is made of two wide strips, separated by a fiberglass sheet d = 0.5 mm thick which has a relative permittivity of 3.5. Neglect any effects due to the edges of the strips (that is, assume the strips are infinitely wide) and calculate:

(a) The lowest TM mode possible.

(b) The lowest TE mode possible.

(c) If a wave at twice the lowest TE cutoff frequency propagates along the waveguide, calculate the wave impedance for the TE and TM modes and compare with the wave impedance for TEM modes.

Reference no: EM131213205

Questions Cloud

What is the lowest frequency signal received at the receiver : What is the lowest frequency signal received at the receiver. Disregard reflections at the connection between the two waveguides.
Use the cost method to account for the purchase of treasury : Recording Stock Transactions Irons Incorporated entered into the following stock transactions: Apr. 5 Issued 28,500 shares of $3 par value common stock for $171,000. May 31 Purchased 1,010 shares of treasury stock for $50,100. Oct. 1 Issued 3,700 sha..
Are credit cards or debit cards money : 1. Are credit cards or debit cards money? Explain your answer. 2. "When the Fed makes an open market purchase of government securities, the quantity of money will eventually decrease by a fraction of the initial change in the monetary base." Is th..
Calculate the lowest tm mode possible : If a wave at twice the lowest TE cutoff frequency propagates along the waveguide, calculate the wave impedance for the TE and TM modes and compare with the wave impedance for TEM modes.
What will be the effect on net operating income of company : Bed & Bath, a retailing company, has two departments, Hardware and Linens. The company’s most recent monthly contribution format income statement follows: Department Total Hardware Linens Sales $ 4,320,000 $ 3,120,000 $ 1,200,000 Variable expenses 1,..
Rate of interest to finance your college education : You borrow money at a fixed rate of interest to finance your college education. If the rate of inflation unexpectedly slows down between the time you take out the loan and the time you begin paying back it back, is there a redistribution of income..
Demand for product x : Assume that the demand for product X is represented by the following equation: QDX = 1000 - 10PX - 5PY + 2PZ. Which of the products Y and Z is a substitute to X in consumption?
Open-outcry descending bid auction : The auction is an open-outcry descending bid auction in the interest rate. How does this auction design deter collusion by the bidders? Is there a better anti-collusive auction design that typically results in the municipality recovering the full ..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Temperature of the steam entering the turbine

Steam is produced at 70 bar and some unknown temperature. A small amount of steam is bled off just before entering a turbine and goes through an adiabatic throttling valve to atmospheric pressure. The temperature of the steam exiting the throttling v..

  The outlet area and velocity are 001 ft2 and 10 fts

a steady-flow compressor is used to compress helium from 15 psia and 70of at the inlet to 200 psia and 600of at the

  Write two second order differential equations

Write two second order differential equations which describe the forces on each mass. Do this in the comments of your code. (Hint: Newton's Law F=ma, Hooke's law F=-kx.,F=Force, m=mass, a=acceleration, k=spring constant, x=displacement from equili..

  Find athe velocity when x2meters b the position were the

the acceleration of a particle is defined as a25-3x2 a is expressed in msec2 and x is in meters. the particle starts

  Convection heat transfer coefficient of the liquid ammonia

Air in an ideal Diesel cycle is compressed from 4L to .25L, and then it expands during the constant pressure heat addition process to 0.50L. Under cold air conditions, how much is the thermal efficiency of this cycle?

  Calculate the volume flow rate of kerosene

For a pressure difference of 0.53 psi across the orifice, calculate the volume flow rate of kerosene.

  Determine the frequency response

A causal discrete-time LTI system is described by y [n] - fr [n - 1] + i y [n - 2] = x [n] where  x [n]  and y [n] are the input and output  of  the system, respectively.

  Oil a has a viscosity of 80cst at 40c and 8cst at 100c oil

two oils are tested to establish their viscosity index. oil a and oil b have their viscosity measured at temperatures

  The lowest temperature that has been achieved is about 1

the lowest temperature that has been achieved is about 1 times 10-6 k. to achieve this an additional stage of cooling

  Abrasive machining-honing-lapping and surface grinding

Define and identify unique characteristics of the items below: Abrasive Machining, Honing, Lapping, Surface Grinding, Centerless Grinding.

  Determine the angular acceleration of the sphere

F17-16. The 20@kg sphere rolls down the inclined plane without slipping. Determine the angular acceleration of the sphere and the acceleration of its mass center.

  Calculate the radiant heat loss if the surface

Calculate the radiant heat loss if the surface emissivity is 0.6. 1-23 A flat wall is exposed to an environmental temperature of 38?C.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd