Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
A three-phase wye-delta transformer is rated 225-kV:24-kV, 400 MVA and has a series reactance of 11.7 ohms as referred to its high-voltage terminals. The transformer is supplying a load of 325 MVA, with 0.93 power factor lagging at a voltage of 24 kV (line-to-line) on its low-voltage side. It is supplied from a feeder whose impedance is 0.11 + j2.2 ohms connected to its high-voltage terminals.
For these conditions, calculate:
(a) the line-to-line voltage at the high-voltage terminals of the transformer
(b) the line-lo-line voltage at the sending end of the feeder.
Write a program that generates 50 floating-point random numbers in a range from 0 to 10,000 using different seed values. Five floating-point random numbers per line are required to be displayed on the ouput.
The configuration is shown in Figure 6.5. Use six LEDs as shown in Table 6.1 to represent the outputs. The Time in This State can be met in several ways. One method is to use a debounced switch as input, another to input a 1 Hz clock.
Design Problem- the circuit must have the following transfer function: Tv(s)=+- (s+125)(s+500)/(s+250)(s+1000) a)design the circuit using two Omp-amps B) design a circuit using only one omp-amp c) design a circuit using no omp amp *in all designs ..
Efficiency in a power transformer is 98.6% when loaded such that its core losses equal the copper losses. Calculate the per unit resistance of this transformer.
a. Design a 3 bit combinational circuit 2's complimenter. (the circuit generates the 2's compliment of the input 3-bit binary number). [Show all work leading to the circuit implementation]
Determine the voltage required on the input of the amplifier to give the maximum output of 85 dBuV. If the signal level from the aerial is 5 dBmV and the input noise level is 20 dBuV, calculate the signal-to-noise ratio on the output of the amplifi..
A 500kVA ,7200-240V, 60Hz, transformer with 2.2% impedance was severly damaged as a result of a dead short across secondary terminals. Determine a) The short-circuit current;
Using the message signal m(t) = 1/(1+t^2) , determine and sketch the modulated signals for the following methods of modulation: (c) SSB modulation with only the upper sideband transmitted. (d) SSB modulation with only the lower sideband transmitted.
A cyclotron used to accelerate alpha [articles (m=6.55 x 10^-27kg, q=3.2x10^19C) has a radius pf .50, and a magnetic field of 1.8T (a)what is the period of revolution of the alpha particles (b)what is their kinetic energy
How many atoms are found inside a unit cell of a simple cubic, body-centered cubic, and faced-centered cubic crystal How far apart interms of lattice constant a are nearest neighbor atoms in each case, measured from center to center
calculate inductance of sensor for air gap of 1mm and 3mm?
The operational amplifier below has a specified input-bias current IIBup to 250nA and a maximal input-offset voltage VOS of ±3mV. It has a unity-gain frequency (gain-bandwidth product) of 1MHz.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd