Calculate the lengths of the stubs

Assignment Help Mechanical Engineering
Reference no: EM131213298

Application: Double stub matching. An antenna has an impedance of 68+j10Ω. The antenna needs to be connected to a 75 n line. Because the antenna goes on a mast, the design engineer decided to fabricate a matching section as shown in Figure 15.38. The matching section is then hoisted and connected to the antenna during installation. At the required frequency, the section is 0.3λ and two stubs are made of the same line. Calculate the lengths of the stubs, if the antenna is connected at A-A.

27_26c054b0-20d3-441b-a4be-a566effda1a9.png

Reference no: EM131213298

Questions Cloud

Government regulation of prices : Usually attempts to control prices are a response to the view that market prices are not always "fair." Therefore, government regulation of prices is based on equity issues.
Write an annotation that summarizes the information : Write an annotation that summarizes the information, evaluates if the information is correct, reviews the author's authority on the topic, and describes how the information is related to the topic.
Discuss problems with the early the research done by bsf ltd : Discuss problems with the early the research done by BSF Ltd. Define and discuss the nature of and differences between research and development (R&D). Also, discuss how research and development are accounted for, why the differences, and why firms ..
Problem regarding the operations management : Describe what the term "Operations Management" means and be able to apply it within organizations.
Calculate the lengths of the stubs : At the required frequency, the section is 0.3λ and two stubs are made of the same line. Calculate the lengths of the stubs, if the antenna is connected at A-A.
Why is it important that prices are flexible in the economy : Why is it important that prices are flexible in the economy? Do you think government should be involved in manipulating prices?
List dash diet dinner recipes to lower blood pressure : List 6 Dash diet dinner recipes to lower blood pressure and cholesterol level for a 68 years old African American woman who has total cholesterol of 320, LDL of 200 and HDL of 28. Includes Nutritional Facts for each recipes and rational for eating..
What is a financial system : What is a financial system and why would a country with a well developed and fully functional financial system be better off than a country without it?
Assuming that periodic inventory system : Romanoff Industries had the following inventory transactions occur during 2015: Units Cost/unit 2/1/15 Purchase 54 $45 3/14/15 Purchase 93 $47 5/1/15 Purchase 66 $49 The company sold 150 units at $70 each and has a tax rate of 30%. Assuming that a pe..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd