Calculate the initial angular acceleration

Assignment Help Mechanical Engineering
Reference no: EM13217898

A dump truck is shown in the figure. The loaded container has a mass of 8000 Kg and may be modelled as a solid homogeneous block. The hydraulic cylinder applies a force of 300 kN to the container in the starting position shown. Calculate the initial angular acceleration of the container for the following conditions:

a. if the truck is not moving,
b. if the truck has a forward acceleration of 3 m/s2.

 

Reference no: EM13217898

Questions Cloud

Explain initiatives aimed at improving healthcare : over the past 20 years there have been several initiatives aimed at improving healthcare in rural America. What are these initiatives? Describe their impacts to date. Is rural health care getting better in the U.S.? Support your answer.
Determine the time required for the shaft to come to rest : The angular acceleration of a shaft is defined by the relation a = -0.25w, where a is expressed in rad/s^2 and w in rad/s. Knowing that at t=0 th angular velocity of the shaft is 20 rad/s, determine the time required for the shaft to come to rest.
Determine the initial acceleration of the projectile : This problem came from the "kinematics of particles" part holding the "Determination of the motion of a particle" section, so use the formula relating to this section of this part.
Explain what is strategy : To what extent is the Hamel & Prahalad article a development of Porter's "What is Strategy?" article and to what extent does it represent an independent approach?
Calculate the initial angular acceleration : A dump truck is shown in the figure. The loaded container has a mass of 8000 Kg and may be modelled as a solid homogeneous block. The hydraulic cylinder applies a force of 300 kN to the container in the starting position shown.
How many lunch tickets can they sell today : The school cafeteria has found that they go through 9 sandwiches for every 6 tickets they sell to the students. Today they have 558 sandwiches available. How many lunch tickets can they sell today?
Determine the principal planes and principal stresses : Knowing that the bracket AB has a uniform thickness of 5/8 in., determine the principal planes and principal stresses at point H.
Which of the two paragraphs has stronger paragraph unity : The legend-in Africa-that all elephants over a large geographical area go to a common "graveyard" when they sense death is approaching led many hunters to treat them with special cruelty. Ivory hunters, believing the myth and trying to locate such..
Explain what was the productivity index for chester : The direct labor costs for Chester were $32,460. These labor costs could have been $20,000 higher if investments in training that increased productivity had not been made. What was the productivity index for Chester that led to such savings?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd