Calculate the impedance at resonance

Assignment Help Electrical Engineering
Reference no: EM132143168

Nanotechnology Engineering - Resonance Circuits Questions -

Q1) A series RLC network has R = 2KΩ, L = 40mH and C = 1μF. Calculate the impedance at resonance and at one-fourth, one-half, twice, and four times the resonant frequency.

Q2) Design a series RLC circuit with BW = 20 rad/s and ω0 = 1000 rad/s using R = 10Ω. Find the quality factor of the circuit (Qs).

Q3) A circuit consisting of a coil with inductance 10mH and resistance 20 is connected in series with a capacitor and a generator with an rms voltage of 120V. Find:

a. The value of the capacitance that will cause the circuit to be in resonance at 15kHz.

b. The current through the coil at resonance.

c. The quality factor of the circuit (Qs).

Q4) A parallel resonant circuit with quality factor 120 has a resonant frequency of 6Mrad/s. Calculate the bandwidth and half-power frequencies.

Q5) A parallel RLC circuit is resonant at 5.6MHz, has a Qp of 80, and has a resistive branch of 40Ω. Determine the values of L and C in the other two branches.

Q6) A parallel RLC circuit has R = 5KΩ, L = 8mH, and C = 60μF. Determine:

a. The resonant frequency.

b. The bandwidth.

c. The quality factor (Qp).

Q7) Find the resonant frequency of the circuit shown.

1446_figure.png

Reference no: EM132143168

Questions Cloud

How does the order you have chosen make sense : After examining the list, explain why you have set up the paragraphs( ideas) in this order. How does the order you have chosen make sense and help the reader.
Price elasticity of demand elastic or in elastic : a) Calculate the price elasticity if demand involved here (correct to 2 decimal places)
Expansionary monetary policy : Does this signal that the Fed is moving toward a more expansionary monetary policy? Why or why not?
Direct part of the federal government : Why was it made an independent quasi-governmental body and not a direct part of the federal government?
Calculate the impedance at resonance : Nanotechnology Engineering - Resonance Circuits Questions - Calculate the impedance at resonance and at one-fourth, one-half, twice
Determine why ophelia goes mad : King Claudius offers perspectives on why Ophelia goes mad, but he is hardly a dependable character. Based on the form that her madness takes, in a post.
Explain the concepts of ethical decision-making : Analyze and apply the concepts of ethical decision-making, corporate governance, and corporate social responsibility.
Describe a public space that you had visited : Describe a public space that you had visited ( i would prefer you write about Starbucks or Walgreen and walmart etc..) describe that space, and explain why you.
Determine range of frequencies that passed by RLC filter : NANENG 203 Nanotechnology Engineering Program Assignment - Passive Filters. Determine range of frequencies that will be passed by a series RLC bandpass filter

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Write matlab command to plot magnitude and phase response

Use the above transfer function and BLT to design a corresponding IIR digital lowpass filter with a cutoff freqency of 15 Hz and a sampling rate of 120 Hz. a. Write the transfer function of the digital filter.

  How much work is required to move one of the charges

Three equal point charges Q form the corners of an equilateral triangle of side length "a". How much work is required to move one of the charges to a point half-way between the other two.

  Need a matlab code for cama

Need a matlab code for CAMA\CD protocol. there should be 3 channel, 4 source. in this code i want to show how much data packet is transmitted and the number of collision and percentage of data loss.

  A sunchronous motor with negligible armature

A sunchronous motor with negligible armature resistance runs at a load angle of 20o at the rated frequency.  if the supply frequency is increased by 10%, keeping other parameter constant, the new load angle

  What is highest blocker level that allows a signal to noise

If the receiver has a phase noise of -100 dBc/Hz, what is the highest blocker level that allows a signal-to-noise ratio of 30 dB? Neglect other sources of noise.

  Compute the power of the water exiting the penstock

A penstock is used to bring water from behind a dam into a turbine. the effective head is 20 m and the flow rate of water is 50m^3/s. Compute the power of the water exiting the penstock.

  A uniformly doped silicon pn junction

A uniformly doped silicon pn junction at T = 300 K, with Na = 1018 cm-3, is to be designed such that at a reverse-bias voltage of 10 V, the maximum electric field is limited to εmax =105 V/cm. Determine the maximum doping concentration in the n-regio..

  To what angle does this mean correspond

These rescaled measurements X are found to follow a beta distribution with a = 4 and β = 2. Find E(X). To what angle does this mean correspond?

  How a dual converter is operated in the motoring

describe how a dual converter is operated in the motoring and generating modes.

  What is overall gain measured from the source to the load

An amplifier represented with an input resistance of 10k ohm, an output resistance of 1k ohm, and the open circuit voltage gain of 1000 V/V is connected to a signal source of 10 mV peak amplitude with an internal resistance of 100k ohm.

  Find the resistance r1 of given figure

Find the resistance R1 of given figure such that the resistor R4 will receive maximum power.

  Determine how many channels in the system are usable

A 24 signal each of 5kHz base band bandwidth are FDM multiplexed using SSB sub carrier modulation. the composite multiplexed signal y(t) is frequency modulated using100MHz carrier frequency.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd