Calculate the heat flux from the surface

Assignment Help Mechanical Engineering
Reference no: EM131136575

1. A 1 m long flat plate is heated with an electrical heater which supplies a uniform heat flux. Air at 25°C is flowing over the surface with a velocity 50 m/s. Plate surface temperature at x = 0.1 m is measured as: Tr = 71°C.

a. Calculate the heat flux from the surface.

b. Calculate the surface temperature at x = 1 m.

Use the following properties of air for calculations: v = 1876 x 10-5 m2/s, k = 0.0284 W/(mK), Pr = 0.703.

2. We want to design a heat exchanger using 7 tubes per row in the direction perpendicular to the flow (NT = 7) due to space requirements. The heat exchanger will use an aligned arrangement of 40-mm diameter tubes with ST - SL = 80 mm and a tube length of 1 m. Water with approach temperature T = 14oC and velocity 1 m/s flows over the tubes. Wall temperature of the tubes is 100°C due to steam condensation inside the tubes. The properties of water at an assumed mean temperature arc given as: p= 993 Kg/m3, μ = 695 x 10-6 Ns/m2, k = 0.628 W/(mK), v = 7 x 10-7 m2/s, e = 4.178 KJ/(KgK), Pr = 4.62. Make sure to use a correlation that fits given properties.

If it is expected that NL > 20 rows, what is the average heat transfer coefficient?

If the average heat transfer coefficient is 1.429 x 104 W(m2K), and if we want the temper-mare of the water leaving the tube bank to be 60oC, how many rows of tubes In the flow direction should be used?

Reference no: EM131136575

Questions Cloud

What are the contribution margin and the margin ratio : What are the contribution margin and the contribution margin ratio for the company in Problem 1 if $15,000 of the overhead is considered variable overhead?
Why it affects fluctuations in output. : Why do we call mechanisms such as proportional income taxes and the welfare system automatic stabilizers ? Choose one of these mechanisms and explain carefully how and why it affects fluctuations in output.
Review key points of the case found in lexis-nexis database : Briefly review the key points of the case found in the Lexis-Nexis database. Explain how greater involvement by the Human Resources Department or Division and diligent adherence to the Annual Human Resources Operating Plan.
Determine the company total profit for the year : A construction company has total revenues of $1,150,000, total construction costs of $956,000, and general overhead costs of $159,000 for the year. Determine the company’s total profit for the year and the percentage of the construction revenues that..
Calculate the heat flux from the surface : A 1 m long flat plate is heated with an electrical heater which supplies a uniform heat flux. Air at 25°C is flowing over the surface with a velocity 50 m/s. Plate surface temperature at x = 0.1 m is measured as: Tr = 71°C. Calculate the heat flux..
What is the equilibrium level of income in this case : If I rises to 100 (we discuss what determines I in later chapters), what will the effect be on the equilibrium income?
What is in the food item you have selected : What is in the food item you have selected? Look at the following: http://ndb.nal.usda.gov/ Suppose Mayo Clinic wisdom and biblical wisdom seem to conflict. Which source will you defer to and why?
What is the new equilibrium income : Is the equilibrium level of income higher or lower than it was in problem 1( a )? Calculate the new equilibrium level, Y , to verify this.
How we benefit from bacteria living on or inside our bodies : Explain how we benefit from bacteria living on or inside our bodies. Please research and give background information on the Human Microbiome Project:

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The turbine is located 75 m below the water surface if the

a river running at 500 m3s is collected in a reservoir behind a dam. the turbine is located 75 m below the water

  Determine the mass of the water and the magnitude and

the piston-cylinder assembly shown in the figure is fitted with a linear spring. the spring constant is k 15 knm and

  Calculate the magnitude of the force

The light bracket ABC is freely hinged at A and is constrained by the fixed pin in the smooth slot at B. Calculate the magnitude R of the force supported by the pin at A under the action of the 80- N · m applied couple

  The player pulls his hand back during the impact at an

a baseball player catching a ball can soften the impact by pulling his hand back. assuming that a 5-oz ball reaches his

  Calculate reynolds number for the process

Calculate Reynolds number for the process and hence the head loss due to friction. State any assumptions made and calculate the minor head losses for the system using both the equivalent length method and the number of velocity heads method.

  The true stress-strain curve of a material obeys the

the true stress-strain curve of a material obeys the power-hardening law with n 0.18. a piece of this material was

  True stress-strain curve of a material

The true stress-strain curve of a material obeys the power-hardening law with n = 0.18. A piece of this material was given a tensile strain of ε = 0.03 before being sent to a laboratory for tension testing. The laboratory workers were unaware of th..

  Evaluate the work transfer in kj if a n 0 b n 1 c n 14

a gas in a piston-cylinder device is compressed through a combination of external force on the piston and cooling in

  A golfer hits a ball giving it a maximum height of 20

a golfer hits a ball giving it a maximum height of 20 meters. the ball lands 130 meters away at the level which he hit

  Modeling the air as ideal gas with constant specific heats

Air is contained in a piston-cylinder assembly, initially at 40 lbf/in2 and 600 ?R. The air expands in a poly tropic process with n = k = 1.4 until the volume is doubled. Modeling the air as an ideal gas with constant specific heats,

  Consider the flow of air over a vertical flat plate at a

consider the flow of air over a vertical flat plate at a low velocity u1 in ambient pressure p1. the plate surface

  Determine the diameter of the nozzle

Steam expands isentropically through a  converging nozzle operating at steady state from a large tank at 1.83 bar, 2808C. The mass flow rate is 2 kg/s, the flow is choked, and the exit plane pressure is 1 bar. Determine the diameter of the nozzle,..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd