Calculate the hall field and hall voltage

Assignment Help Electrical Engineering
Reference no: EM13246605

Germanium is n-type doped at 5x1015 cm-3 at T=300 K. The dimensions of the Hall device are d=5x10-3 cm, W=2x10-2 cm, and L=10-1 cm. The current is Ix=250 A, the applied voltage is Vx=100 mV, and the magnetic flux density is Bz= 500 gauss=5x10-2 T. Calculate: (a) the Hall voltage, (b) the Hall field

Reference no: EM13246605

Questions Cloud

Explain evaporating liquefied dichlorodifluoromethane : Some refrigerators cool their contents by evaporating liquefied dichlorodifluoromethane CCl2F2. How many kg of this liquid must be evaporated to freeze a tray of ice cubes at room temperature (25 degrees C) Delta H fusion= 6.01 kJ/mole
Which should be the signal power in the given case : A cable technician tested the signal-to-noise ratio on the curb as 20 dBm. This means, if the noise power is at 1 mW, then the signal power should be 20 dB higher then that. If the noise power is 20 mW
Why was european culture and civilization better equipped : Why was European culture and civilization better equipped them to conquer the Inca, Aztec and other “New World” civilizations and not the other way around?
Explain iron nitrate and potassium phosphate react : What is the limiting reactant when equal masses of iron(III) nitrate and potassium phosphate react in solution?
Calculate the hall field and hall voltage : Germanium is n-type doped at 5x1015 cm-3 at T=300 K. The dimensions of the Hall device are d=5x10-3 cm, W=2x10-2 cm, and L=10-1 cm. The current is Ix=250 A, the applied voltage is Vx=100 mV, and the magnetic flux density is Bz= 500
Determine the current density in the wire : The starter motor of a car engine draws an electric current of 42.0 A from the battery. The copper wire to the motor is 6.00 mm in diameter and 1.71 m long, What is the current density in the wire
Discuss the challenges that confronted africa''s independence : What lead to the decolonization in Africa. Discuss the challenges that confronted Africa's independence.
Explian gases effuses at approximately one-half that rate : at 25 C, a sample of NH3(molar mass= 17g/mol) effuses at a rate of .050 mole per min. under the same conditions, which of the fallowing gases effuses at approximately one-half that rate
What is the no load terminal voltage of the generator : given data: RA = 0.18 ohm, Radj = 10 ohm, NF = 1000 turns per pole, VF = 120V, RF = 20 ohm. This is a shunt connected generator with a speed of 1800 r/min. A. what is the no load terminal voltage of the generator

Reviews

Write a Review

Electrical Engineering Questions & Answers

  What local oscillator frequency would you use

For the local oscillator you selected, what transmission frequencies could cause interference to the satellite system and how could the interference be avoided? Show a diagram.

  Calculate the required junction area of pn jucntion

A certain pn junction is operating with Vt=26mV and ni=1.08x10^10 electrons/cm^3. The doping concentrations are Na=2x10^15 cm^-3 and Nd=9x10^16cm^-3. The diffusion coefficient are Dn=34cm^2/s and Dp=12cm^2/s.

  Design an rc-low pass filter

Design an RC-Low Pass Filter with cutoff frequency at fc=0.5GHz and plot its frequency response and design a parallel resonance circuit with resonance frequency of 30kHz and bandwidth of 20kHz and plot its frequency response.

  How high can vce go without exceeding

A certain transistor is to be operated at a collector current of 50mA. How high can VCE go without exceeding a PD(MAX) of 1.2W?

  Sketch the dft

Sketch the DFT(discrete fourier transform)for a square wave with frequency 1Hz and 10 Hz given N=64 and SR(sample rate)=128. Make sure to label your axes.

  Estimate the maximum gain and the frequency

a) construct the straight-line Bode plot of the gain. Is this a low-pass, high-pass, bandpass, or bandstop function b) Use the straight-line plot to estimate the maximum gain and the frequency at which it occurs.

  Explain power factor correction

Power factor correction, Three parallel impedances in rectangular form as follows

  Find the output frequency when the input frequency

A system samples a sinusoid of frequency 480 Hz at a rate of 100 Hz and writes the sampled signal to its output without further modification. Determine the frequency that the sampling system will generate in its output.

  Determine the velocity of b relative to a

Racecar A is traveling on a straight portion of the track while racecar B is traveling on a circular portion of the track. At the instant shown, the speed of A is increasing at the rate of 10 m/s2, and the speed of B is decreasing at the rate of 6..

  Design a collision free circuit for a router

A network router connects multiple computers together and allows them to send messages to each other. If two or more computers send messages simultaniously, they collide and the messages must be resent. Design a collision free circuit for a router..

  What are the variables-unknowns that we are solving for

mesh analysis involves writing and solving a number of simultaneous equations. The number of equations is equal to the number of independent loops in the circuit. Each equation is derived from the application of KVL around the loop.

  What is the velocity of propagation in the cable

A certain transmission line is 10 meters long. Measurements indicate that the total inductance of the cable is 16 uH. Standing wave measurements indicate that the voltage reflection coefficient at the load is 0.5 + j0

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd