Calculate the forces exerted by the water on the bend

Assignment Help Civil Engineering
Reference no: EM13210825

Water flows through a horizotal 45 deg reducing bend with a 36 inch. diameter upstream and a 24 inch diameter downstream, at the rate of 20 cfs under a pressure of 15 psi at the upstream end of the bend. Neglecting head loss in the bend, calculate the forces exerted by the water on the bend.

Reference no: EM13210825

Questions Cloud

Create a primary function : create a primary function that uses a function handle with a nested function to compute the ninimum of the function 20x^2-200x+12 over the range 0
Determine the pressure head at the nozzle inlet to produce : determine the pressure head at the nozzle inlet to produce a water jet velocity of 40 ft/s. Neglect the friction loss and assume incompressible flow.
Determine the flow rate of the oil : Oil of a specific gravity of 0.75 is flowing through a 6-in pipe under a pressure of 15 psi. If the total energy relative to the datumplate is 8.0 ft below the center of the pipe is 58.6 ft, determine the flow rate of the oil.
Compute the equilibrium pressure of no : Calculate the equilibrium pressure of NO if 2.00 atm and 1.00 atm of O2 are initially placed in a 1.0L container at 440K and the final total pressure in the container
Calculate the forces exerted by the water on the bend : Water flows through a horizotal 45 deg reducing bend with a 36 inch. diameter upstream and a 24 inch diameter downstream, at the rate of 20 cfs under a pressure of 15 psi at the upstream end of the bend. Neglecting head loss in the bend, calculate..
Explain the photoelectron spectrum of n2 : write the MO configuration of N2^+ and terms symbol for the ground state and excited states. show the photoelectron spectrum of N2. Assign short and long progression band.
Summary on low-fat diets vs. low-carb diets : I have to write a summary on low-fat diets vs. low-carb diets andwhether both diets help to lose weight, lower blood cholesterol, & improve glucose tolerence.
Use reduction-potential values to describe acidic solution : Use reduction-potential values to explain which halides can be oxidized by Fe3+ or by MnO4- in acidic solution?
Calculate for the ground distance of the angular coverage 60 : If an aerial photograph is taken with this camera tilted angle­­A=35° at an altitude 5000ft., calculate for the ground distance of the angular coverage 60°.

Reviews

Write a Review

Civil Engineering Questions & Answers

  What is the elevation of the tip of the spire

The telescope of the instrument is 5.25 ft above the ground station, whose elevation is 415.65 ft. What is the elevation of the tip of the spire? (Ignore atmospheric refraction and earth curvature)

  What is the concentration of tracer in the reactor

What is the concentration of tracer in the reactor 1 h after tracer addition is terminated? The reactor had an initial concentration of tracer of 1.0 mg/L when tracer addition commenced.

  What is the maximum acceleration from rest

The base engine develops 200 ft-lb of torque, and a modified version of the engine develops 240 ft-lb of torque. If the overall gear reduction ratio is 8 to 1, what is the maximum acceleration from rest (in ft/sec^2) for.

  What will be the total vehicle delay

Assuming D/D/1 queuing, what will be the total vehicle delay?

  Hypothetical velocity distribution in a horizontal channel

The hypothetical velocity distribution in a horizontal, rectangular open channel is V=0.3y (m/s), where V is the velocity at a distance y (m) from the bottom of the channel. If the vertical depth of flow is 2 m and the width of the channel is 4 m,..

  Determine the horsepower of the device

water flows from a lake as is shown in fig. p8.40 at a rate of 4.0 cfs. is the device inside the building a pump or a turbine? Explain and determine the horsepower of the device. neglect all minor losses and assume the friction factor is .025

  Formulate the shear and bending moment expressions

Show/formulate the shear and bending moment expressions for each board, and plot/draw the shear and bending moment diagrams of the boards.

  Enforcement team investigating possible dumping of arsenic

Suppose you are a member of an EPA enforcement team investigating the possible dumping of arsenic into Arbor Lake. You take water samples from the middle of the lake and find that the concentration is 90.0 ppb.

  Largest principal stresses and maximum shear stress

The shaft diameter is 100 mm. Calculate the largest principal stresses and maximum shear stress that will occur in the shaft.

  How much caco3 is produced per hour

A slurry containing 20 percent by weight of limestone (CaCO3) is processes to separate pure dry limestone from water. If feed rate is 2000kg/h, how much CaCO3 is produced per hour?

  Evaluation of engineering projects

Why is the ‘time value of money' important for the evaluation of engineering projects? Provide at least one practical example to support your view (max 2 pages).

  What is the equivalency factor for the 14 kip single axle

What is the equivalency factor for the 14 kip single axle?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd