Calculate the force that caused the fracture

Assignment Help Mechanical Engineering
Reference no: EM131275307

A three-point bend test is performed on a block of silicon carbide that is 10 cm long, 1.5 cm wide, and 0.6 cm thick and is resting on two supports 7.5 cm apart. The sample breaks when a deflection of 0.09 mm is recorded. The flexural modulus for silicon carbide is 480 GPa. Assume that no plastic deformation occurs. Calculate

(a) the force that caused the fracture; and

(b) the flexural strength.

Reference no: EM131275307

Questions Cloud

Which molecules remained inside of the dialysis bag : Why is it necessary to have positive and negative controls in this experiment? Which molecules remained inside of the dialysis bag? Did all of the molecules diffuse out of the bag into the beaker? Why or why not?
Determining the network manager : Think of a security policy you may have encountered either at school or in the workplace. Why do you suppose it was set up that way? Do you think it was effective? Would you arrive at the same solution if you were a network manager?
What controls the strength of glasses : Sketch a schematic of the strength of ceramics and that of metals and alloys as a function of probability of failure. Explain the differences you anticipate.
Explain the significance of the weibull distribution : A cylindrical tool steel specimen that is 6 in. long and 0.25 in. in diameter rotates as a cantilever beam and is to be designed so that failure never occurs. Assuming that the maximum tensile and compressive stresses are equal, determine the maxi..
Calculate the force that caused the fracture : A three-point bend test is performed on a block of silicon carbide that is 10 cm long, 1.5 cm wide, and 0.6 cm thick and is resting on two supports 7.5 cm apart. The sample breaks when a deflection of 0.09 mm is recorded.
Common multiple of zero : You can use ab/g to compute the least common multiple of two integers, a and b, where g is the greatest common divisor of a and b. For example, the least common multiple of 4 and 6 is 12. Write a maple procedure, LCM, which take as input n>0 integ..
What information might a doctor want before prescribing : What information (other than Kirby-Bauer results) might a doctor want before prescribing one of these medications to a patient? What might a pharmacist ask before filling the prescription? Do NOT tell me what a researcher would want.
Watch the movie oleanna and write a review about the film : Watch the movie oleanna and write a review about the film. Write a contrast between institutional styles of Collage nowadays and the school depicted in the film, OR your reaction to the film's depiction of higher education from the perspective of ..
Write what you like and whod you dont like : This is a Hospitalty assignment. Our task on this assignment is to write 1 page about Reastaurants that was given to us by our instructor. make sure that you use your own words to write thus pages.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Calculate the fraction of the water that condenses and the

air at 80 degrees fahrenheit and 80 percent relative humidity is cooled to 51 degrees fahrenheit at a constant pressure

  If the coefficient of restitution between each car is85

at a amusement park there are 180kg bumper cars a b and c that have riders as shown with masses 40 kg 60kg and 30 kg

  A piston-cylinder device initially contains

A piston-cylinder device initially contains 0.4 m3 of air at 100 kPa and 80°C.The air is now compressed to 0.1 m3 in such a way that the temperature inside the cylinder remains constant. Determine the work done during this process.

  Water behind a dam enters an intake pipe at 24psia 5 fts

water behind a dam enters an intake pipe at 24psia 5 fts flow through a turbine and exits 200ft below at 19psia 45 fts

  A rankine power cycle operates with an open feedwater

a rankine power cycle operates with an open feedwater heater. the boiler pressure is 6.0 mpa. a superheater provides a

  Horizontal chromium-plated surface

Saturated ethylene glycol at 1 atm is heated by a horizontal chromium-plated surface which has a diameter of 200 mm and is maintained at 480 K. Estimate the heat- ing power requirement and the rate of evaporation.

  If the total flow rate of gas out of the stack is 190

a stack was sampled for 8 minutes. the gas velocity at stack conditions through the sampler was 15.0 ms and the area

  What is the principle of precipitation hardening

What is a supersaturated solution? How do we obtain supersaturated solutions during precipitation hardening? Why is the formation of a supersaturated solution necessary?

  Temperature of refrigerant at end of the heating process

A rigid tank is heated for 9 minutes with a 800W electrical heater. During this time 70kJ of energy is lost due to heat transfer to the environment. Find the temperature of the refrigerant at the end of the heating process.

  You are manufacturing a frame for a vehicle out of some

you are manufacturing a frame for a vehicle out of some aluminum alloy 6061-t451 tubing. the frame is to be welded

  Determine the force which must be applied normal

Determine the force F which must be applied normal to the handle at C in order to (a) tighten and (b) loosen the clamp. Neglect friction at point A.

  Write a loop-closure equation for this mechanism

If the input is the displacement of the cylinder, what are the unknowns?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd