Calculate the force of attraction

Assignment Help Mechanical Engineering
Reference no: EM13217083

Calculate the force of attraction between a K+ cation and a O2- anion, the centers of which are separated by a distance of 1.5 nm.

Reference no: EM13217083

Questions Cloud

Determine the magnitudes of forces fa and fb acting on each : determine the magnitudes of forces FA and FB acting on each chain and the orientation ? of FB so that the magnitude of FB is a minimum.
Derive the operational transfer function : Derive the operational transfer function and the sinusoidal transfer function for an RC high-pass filter. Plot the step response and the complete frequency response (magnitude and phase).
Present a risk assessment of a warehouse : These include risks associated with layout, floors, heating, noise, housekeeping and fire. Review these risks, and in a two page paper (not including the title and reference pages), present a risk assessment of a warehouse
Explain what constructs or concepts might you employ : What constructs or concepts might you employ? Choose several of the major concepts, and specify their dimensions.
Calculate the force of attraction : Calculate the force of attraction between a K+ cation and a O2- anion, the centers of which are separated by a distance of 1.5 nm.
Determine the radius of the crank r : Determine the radius of the crank R and the speed n of a slider crank mechanism, used in a shaker table. It is required that the average speed of the table is 5 m/s, and the maximum absolute acceleration is 3000m/s^2. Assume ratio R/L=0.2
Estimate the mass flow rate of fuel into the engine : Estimate the mass flow rate of fuel into the engine in kg/h.
Derive the linearised equation about the operation : For the pendulum shown in the figure,the restoring torque due to gravity is given by T=mgLsin(thita). Derive the linearised equation about the operation point thita=0.
Explain development of the design more effective : Explain and justify ideas that could have made the development of the design more effective. Support your recommendations with specific examples as appropriate.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Calculate the temperature of the gas in the tank

comment on any safety hazards that might be encountered. especially, what would you anticipate if the inlet gas control valve were to malfunction and the gas space above the fuel were to reach full storage tank pressure (69bar)? the fuel tank has ..

  Evaluate thermal efficiency of the cycle

Evaluate thermal efficiency of the cycle

  Determine the radius of curvature of the path of the package

package is dropped from the plane which is flying with a constant horizontal velocity of vA = 150 ft/s at a height h = 1500 ft. Determine the radius of curvature of the path of the package just after it is released from plane at A.

  Describe the main kinds of social mechanisms

Describe the main kinds of social mechanisms that are used by people to communicate and collaborate.

  Sketch the cycle on p-v coordinates

Two kilograms of air within a piston-cylinder assembly execute a carnot power cycle with maximum and minimum temperatures of 750k and 300k, respectively.

  A trapezoidal channel made out of brick

A trapezoidal channel made out of brick, with bottom width 6ft and with bottom slope 0.001

  Define kinetics of particles -newton''s second law

Kinetics of Particles : Newton's Second Law, Determine the maximum theoretical speed that may be achieved over a distance of 50 m by a car starting from rest

  Define the maximum take-off mass of an airbus

The maximum take-off mass of an Airbus A380 passenger jet is about 600 000 kg. The lift is provided by the wings, which have a total area of 845 m2.

  Determine the average applied force exerted on to the pile

determine the average applied force exerted on to the pile hammer. Note because the force is applied over a short time period it can be considered as an impulse force.

  Determine the one machine that should be selected

If the minimum attractive rate of return is20% per year, determine the one machine that should be selected on the basis of a rate of return analysis.

  Explain what is the basic design load rating

Design life is 9630 hours, rotating at 250 rpm, load of 880 lbs, what is the basic design load rating (assuming no axial loads)?

  What is the inner tube surface temperature at the outlet

What is the inner tube surface temperature at the outlet, where fully developed conditions may be assumed?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd