Calculate the force in cb for this instant

Assignment Help Civil Engineering
Reference no: EM131036362

The uniform slender bar AB has a mass of 0.8 kg and is driven by crank OA and constrained by link CB of negligible mass. If OA has an angular acceleration α0 = 4 red/s2 and an angular velocity ω0 = 2 red/s when both OA and CB are normal to AB, calculate the force in CB for this instant. (Suggestion: Consider the use of Eq. 6/3 with A as a moment center.)

1461_7aa08cea-7ebe-4369-a1a8-9a0339634da2.png

Reference no: EM131036362

Questions Cloud

Determine the resulting angular acceleration and the force : Determine the resulting angular acceleration and the force TA in the strap at A immediately after wheel B rolls off the rail. Neglect friction and the mass of the small straps and wheels.
Hostage at the us embassy by radicals : During the Iranian revolution, a group of Americans was taken hostage at the US embassy by radicals, leading to a serious international incident. For how long were these hostages held?
Influence of historical styles on contemporary interiors : Write a 5-7 page paper that will examine the influence of historical styles on contemporary interiors. Look through Interior Design and Architecture journals, and identify two to four interiors from the past 15 years that reference (directly or ind..
Charles guiteau fatally shot : On July 2, 1881, lawyer and itinerant preacher Charles Guiteau fatally shot recently-elected US President James Garfield. Why?
Calculate the force in cb for this instant : If OA has an angular acceleration α0 = 4 red/s2 and an angular velocity ω0 = 2 red/s when both OA and CB are normal to AB, calculate the force in CB for this instant. (Suggestion: Consider the use of Eq. 6/3 with A as a moment center.)
Write a seven pages paper on topic outsourcing : Write a seven pages paper on topic outsourcing (ethical issues). The paper require seven pages on topic outsourcing (ethical issues) than need to make a power point presentation.
Margins for legible copy-editing : Please complete the review on or before the assigned date. All reviews should be typed and double-spaced with sufficient margins for legible copy-editing.
Determine the moment mb exerted by arm ab on arm bc : The mass of arm BC is 4 kg, and the arm may be treated as a uniform slender rod.
Determine the average p concentration in the runoff : A watershed contains 16.2 ha and 24.3 ha of agricultural and residential land use, respectively. The last rainfall removed all P accumulations and was followed by a 2 day dry period before a 12.7mm rain event with duration = 60 min., P loading ra..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the direction of acceleration at point a

The wheel is rolling to the left without a constant angular velocity without slipping. determine the direction of acceleration at point a?

  The amount of elastic settlement below the axis of the pole

A pole is held vertically on a soil surface by three equally spaced wires tied to the top of the pole. Each wire has a tension of 1 kN and is inclined at 45 degrees to the vertical.

  Design temperature and residence time have been established

The oven exhaust gases are available at 250 F. Assume that the design temperature and residence time have been established as 1300 F and 0.6 sec, respectively. The type of burner used in the process requires outside air at a moass ratio of 12:1

  Calculate the total axial deformation in the aluminum rods

A rigid rectangular shelf is suspended from a rigid ceiling by mean of four rods of diameter .505 inches. The two rods to the left L1 and L2, are made of steel. The two rods to the right R1 and R2 are made of aluminum.

  Calculate the bearing stress on the shaft key

A rotating shaft with an applied torque of 400 Newton-meters is held in place (stopped) by a shaft key. The diameter of the shaft is 15 centimeters. The shaft key has a length of 20 cm, and is square, with its width and height being 5 cm.

  Find the length of the studs in a rake wall with base height

Find the length of the studs in a rake wall with a 5:12 pitch, a half span of 9'4", 16" OC and a base height of 7'3".

  What should be the length of an aluminum wire of 6 mm

What should be the length of an aluminum wire of 6 mm in diameter so it can be twisted one full turn without exceeding a shear stress of 42 MPa G = 27 GPa.

  Determine the rotation angle of end b relative to end a

If a torque of T = 1,100 N-m is applied to the composite assembly, determine: (a) the maximum shear stress in the aluminum tube and in the steel core. (b) the rotation angle of end B relative to end A.

  Minimize the effect of those environmental impacts

Identify the environmental impacts due to land transportation and highway construction - minimize the effect of those environmental impacts.

  What is the discharge per 100 foot wide strip of the aquifer

In one observation well water stands 28.8 ft above the bottom at a radius of 687 ft, and in the other it stands 22.5 ft above the bottom. What is the discharge per 100 foot wide strip of the aquifer in square ft per day

  Determine the force needed to obtain static equilibrium

Create a 60 degree inclined plane utilizing various building components, string, as single pulley , and a scientific mass. attach one end of the string to the scientific mass (resistance force) and the other end to a force-measuring device

  What is the maximum length to which it may be stretched

what is the maximum load that may be applied to a specimen with a cross sectional area of 130 mm^2 without plastic deformation.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd