Calculate the flow rate in each of the branches

Assignment Help Mechanical Engineering
Reference no: EM131174502

In the branched pipe system shown in Fig. 12.8, 850 L/min of water at 10°C is flowing in a DN 100 Schedule 40 pipe at A. The flow splits into two DN 50 Schedule 40 pipes as shown and then rejoins at B. Calculate

(a) the flow rate in each of the branches and

(b) the pressure difference PA - PB·

Include the effect of the minor losses in the lower branch of the system. The total length of pipe in the lower branch is 60 m. The elbows are standard.

2399_60430f58-2a8c-4f3d-b863-1bff009da11d.png

Reference no: EM131174502

Questions Cloud

Assessment at the end of the instructions : Use the assessment at the end of the instructions as a guideline, but again, for where it states "I expect that you will have at least 4 contributions from each author" I find that to be too high a number. 4-8 total would certainly be enough for f..
Interpreting new testament letters : Explain and illustrate the 4 steps of the Interpretive Journey for New Testament letters in Journey into God's Word: Your Guide to understanding and applying the Bible.
Develop a coherently structured paper with an conclusion : Develop a coherently structured paper with an introduction, body, and conclusion. Provide a concluding paragraph / transitional paragraph that summarizes the proposed solution and its advantages.
Mobile computing and wireless computing : Decide whether or not mobile computing and wireless computing are synonymous. Provide at least two (2) reasons to support your assertion and justify your response.
Calculate the flow rate in each of the branches : In the branched pipe system shown in Fig. 12.8, 850 L/min of water at 10°C is flowing in a DN 100 Schedule 40 pipe at A. The flow splits into two DN 50 Schedule 40 pipes as shown and then rejoins at B.
What clarification do you need regarding the posting : What additional questions do you have after reading the posting? What clarification do you need regarding the posting? What differences or similarities do you see between your posting and other classmates' postings?
Bottom of checks and deposit slips : This reading device is readily used in banks to read the numbers on the bottom of checks and deposit slips?
Form that the computer can understand : Devices convert a sketch or a figure into a form that the computer can understand?
Discuss the possibility of switching suppliers : Bargaining power of suppliers: What is the importance of raw materials, components, labor, and services that are required for the industry, and are there substitutes for those inputs? Discuss the possibility of switching suppliers, if necessary.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd