Calculate the flow in the river just downstream

Assignment Help Civil Engineering
Reference no: EM13564957

An industrial wastewater is discharged into a river about 0.5 km downstream from an outfall (discharge) coming from a desalination plant. Upstream of the desalination plant's outfall the river has a flow of 17.8 m3/sec and a total dissolved solids (TDS) concentration of 260 ppm. The water coming from the desalination plant's outfall flows into the river at a rate of 1800 L/sec and has a TDS concentration of 4,450 ppm. The industrial wastewater discharge has a flow of 5.0 m3/sec and a TDS concentration of 860 ppm

a) Calculate the flow in the river just downstream of the desalination plant's outfall (m3/sec).

b) Calculate the flow in the river just downstream of the industrial wastewater discharge (m3/sec). c) Calculate the TDS in the river just downstream of the desalination plant's discharge (ppm). d) Calculate the TDS in the river just downstream of the industrial wastewater discharge (ppm).

Reference no: EM13564957

Questions Cloud

Determine the upstream depth of flow in a subcritical : Determine the upstream depth of flow in a subcritical transition from an upstream rectangular flume that is 49ft wide to a downstream trapezoidal channel with a width of 75ft and side slopes
How much would the volume of 1m^3 of water at 20c : Water is weakly compressible but often assumed incompressible; check the validity of this assumption. Using Table 3.1.2 in the text, how much would the volume of 1m^3 of water at 20C change if subjected to the pressure exerted by a 70m column of wate..
What angle would be needed in order for an equivalent body : The face of a 100m wide rectangular dam is built at an angle of 60 degrees above the horizontal and holds back a body of fresh water that is 30m deep at the face of the dam
What was the distance between the markers : A 100 ft cut steel tape was used to measure between two property markers. The rear surveyor held 93 ft, while the head surveyor cut .67ft. What was the distance between the markers?
Calculate the flow in the river just downstream : An industrial wastewater is discharged into a river about 0.5 km downstream from an outfall (discharge) coming from a desalination plant. Upstream of the desalination plant's outfall the river has a flow of 17.8 m3/sec and a total dissolved solids
What are the final concentrations of no no2 and o3 : A dark atmosphere initially contains no ozone (O3), 100 ppb NO, and 100 ppb NO2. The sun comes comes out and the photostationary state relationship below is achieved in a few minutes. What are the final concentrations of NO, NO2 and O3?
Determine the minimum radius of the new curve if the safe : A curve of radius 300 ft and e = 10% is located at the section of an existing rural highway, which restricts the safe speed at this section of the highway to 40% of the design speed.
Find the theoretical carbonaceous oxygen demand : Suppose a ponds water contains 10.0 mg/L of some algae, which can be represented by the chemical formula C6H15O6N. Using the following reactions:
What are the concentrations of ppm : A sample of air has been collected from above an air stripping tower to evaluate its performance and to determine if toxic air emission standards are being violated

Reviews

Write a Review

Civil Engineering Questions & Answers

  Find the speed of mass b for a given speed of mass a

A moves downward a distance of 3.6 ft, and mass B moves a distance x. What is the value of x 2. Find the speed of mass B for a given speed of mass A The system is released from rest and mass A moves downward at a constant speed of 8.0 ft/s.

  Time inventory system for a product

How appropriate might a just in time inventory system be for a product such as roller skates?

  What is the minimum grade a student must get in order

The mean grade on a final examination was 72, and the standard deviation was 9. The top 10% of the students are to receive A's. What is the minimum grade a student must get in order to receive an A

  Determine the radius of influence of the pumping

The initial piezometric head in a confined aquifer has a thickness of 11.6 m is 85.7 m above sea level. A well with a radius of 0.5 m pumps at a constant rate of 1240 m3/day

  Determine the amount of air that must be bled off to restore

When the air temperature is 25°C, the pressure gage reads 210 kPa. If the volume of the tire is 0.025 m3, determine the pressure rise in the tire when the air temperature in the tire rises to 50°C.

  What is the discharge of each hole

A water of 20 c temprature pupped at 75 kpa to a perforated pipe 5 cm dia. contain 10 hole with the same diameter. the distance between two adjacent hole is 20 cm. what is the discharge of each hole?

  What is the volume of required soil excavated in borrow pit

Soil is excavated from a borrow to construct an embankment with a net volume of 50,000 cy. This is performed by compacting 12-in layers of the soil to a dry weight of 110 pcf at a moisture content of 18%.

  Largest principal stresses and maximum shear stress

The shaft diameter is 100 mm. Calculate the largest principal stresses and maximum shear stress that will occur in the shaft.

  Determine what is the force in the wire and beam

The 5-m long cantilever beam using a W410 x 67 standard wide flange section has a distributed load of 1200 N/m placed on it. It is also supported by a cable at B, of length 2 m with a 7 mm2 cross sectional area. What is the force in the wire

  What concentration of fe needed to maintain phosphate

FeCl3 is added to remove excess phosphate. The following reactions occur (the charges are in parentheses): FeCl3 -> Fe(3+) + 3Cl(-) Fe(3+) + PO4(3-) -> FePO4 The equilibrium constant for the second reaction is 10^26.4.

  Determine the volume and density of the body

The volume and the average density of an irregularly shaped body are to be determined by using a spring scale. The body weighs 7200 N in air and 4790N in water. Determine the volume and density of the body.

  What would the spindle diameter need to be in order

The crane hoists a uniformly distributed load C. the two identical motors at A an power through gearboxes operating at maximum output speed of 100 rpm.the load is lifted by winding cable onto spindles attached to the output shaft of each gear box. Th..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd