Calculate the final temperature and heat loss

Assignment Help Mechanical Engineering
Reference no: EM131285252

A vessel contains a mixture of ethylene (C2H4) and twice as much air as that required for complete combustion. If the initial pressure and temperature are 5 bar and 440 K, calculate the adiabatic temperature rise and maximum pressure when the mixture is ignited.

If the products of combustion are cooled until the water vapour is just about to condense, calculate the final temperature, pressure and heat loss per kmol of original mixture.

The enthalpy of combustion of ethylene at the absolute zero is 1,325,671 kJ/kmol; and the internal energy at 440 K is 16,529 kJ/kmol.

Reference no: EM131285252

Questions Cloud

Should governments limit use of internet for data collection : Do consumers have the right to "own" data about themselves? Should governments limit the use of the Internet for data collection?
Given the answer of the multiple choice questions : Given the answer of the multiple choice questions:The word "religion" literally means,The Way of Faith is normally associated with.
Formula flexible budget : The controller for Rainbow Children’s Hospital, located in Munich, Germany, estimates that the hospital uses 31 kilowatt-hours of electricity per patient-day, and that the electric rate will be €.19 per kilowatt-hour. The European monetary unit €, th..
How are the developers trying to sell the technology : How has this technology been received, accepted, or rejected? Why? Is it feared or favored? What is the attitude toward change? How are the developers trying to sell the technology to the general public?
Calculate the final temperature and heat loss : If the products of combustion are cooled until the water vapour is just about to condense, calculate the final temperature, pressure and heat loss per kmol of original mixture.
Determine the equation for the impulse response : Evaluate the response for a suitable length of time so that the response reaches steady state. Then, determine the magnitude and phase of the output v0 (t) , and compare to the magnitude and phase of your Bode plots at frequency 5,500 rad/sec.
What songs cause radio listeners to change stations : One unobtrusive measure mentioned in this chapter involved going through consumers' or competitors' garbage. Do you think marketers should have the right to do this? Is it ethical?
Create a post that shares : Think about a supervisor you respected greatly, and create a post that shares which base(s) of power you saw operating in him or her. Was there a "down" side to the power he or she displayed? Which two bases of power do you think might be most imp..
Develop the mode and format for data collection : Develop a plan for the research.- Select the techniques you will use to gather data.- Develop the mode and format for data collection.-  Conduct the research.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd