Calculate the equations for the specific heats

Assignment Help Mechanical Engineering
Reference no: EM131285291

The following data refer to an analysis of a dual combustion cycle with a gas having specific heats varying linearly with temperature:

The pressure and temperature of the gas at the end of compression are 31 bar and 227 °C respectively; the maximum pressure achieved during the cycle is 62 bar, while the maximum temperature achieved is 1700
C.

The temperature at the end of the expansion stroke is 1240 °C. The increases in entropy during constant volume and constant pressure combustion are 0.882 and 1.450 kJ/kg K respectively. Assuming that the fluid behaves as an ideal gas of molecular weight, mw - 30.5 calculate the equations for the specific heats, and also the expansion ratio if that process is isentropic.

Reference no: EM131285291

Questions Cloud

Write the response about the consumer behaviour discussion : MRKT 410 7980:Write the response about the Consumer Behaviour Discussion.
How to effectively get the business : Explain to new salesperson the differences among types of purchases and how to effectively "get the business" for all three types of purchases.
Allocate the budgeted overhead costs to the products : Cain Company makes three products in its factory: plastic cups, plastic tablecloths, and plastic bottles. The expected overhead costs for the next fiscal year include the following. Allocate the budgeted overhead costs to the products.
Key discussions from honda : Can you summarize the key discussions from Honda (B) HBR case, and also provide the comparisons between HBR case Honda (B) with Honda (A) HBR case-March 2011 issue? Can you also provide your discussion on leveraging capabilities, and the focus on ..
Calculate the equations for the specific heats : Assuming that the fluid behaves as an ideal gas of molecular weight, mw - 30.5 calculate the equations for the specific heats, and also the expansion ratio if that process is isentropic.
What technology assessment made amory lovins famous : What are the purposes of Technological Assessment? How is this process similar and different from Environmental Assessment - Explain the perspective of technology "questioners" such as Neil Postman? How is this different from the perspective of tech..
How much will profits increase or decrease : Cane Company manufactures two products called Alpha and Beta that sell for $195 and $150, respectively. Each product uses only one type of raw material that costs $5 per pound. The company has the capacity to annually produce 123,000 units of each pr..
What are the planning needs for a smooth transition : What are the planning needs for a smooth transition? What types of resources have you used that were effective and ineffective in transition planning?
Determine the sales volume in dollars and units : Lindo Company incurs annual fixed costs of $46,640. Variable costs for Lindo’s product are $21.76 per unit, and the sales price is $32.00 per unit. Lindo desires to earn an annual profit of $50,000. Required Determine the sales volume in dollars and ..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Investment opportunity

Consider the following investment opportunity: Initial Cost = $126,890; Annual Benefit = $23,000; Useful Life = 30 Years; Salvage Value = $0; What interest rate results in a Benefit Cost Ratio equal to one?

  The flux density of a magnetic field is 20000 lines per sq

the flux density of a magnetic field is 20000 lines per sq in. what length of conductor should cut the flux to produce

  Maximum shearing stress in cylinder after-internal pressure

A laminated thick-walled cylinder was fabricated by shrinking a steel (E=200 GPa and nu=0.03) sleeve having an inside diameter of 199.800mm and an outside diameter of 300mm onto a steel tube with an inside diameter of 100mm and an outside diameter of..

  Estimate the power required to overcome the surface

a racing boat planes over the water at 80 mph. the water temperature is 75f. the wetted surface of the boat i.e. the

  Determine the compressor isentropic efficiency

A compressor is to compress saturated R-134a at 14C to 900 kPa, and a power of 4.6 kW is needed when the flow rate is 0.26 kg/s. Please determine the compressor isentropic efficiency. The temperature at compressor exit

  Determine the heat generated and heat dissipated

A journal bearing is proposed for a steam engine. the load on the journal is 3 kN, diameter 50 mm length 75 mm speed 1600 r.p.m , diametral clearance 0.001 mm ambient temperature 15.5 C oil SAE 10 is used and the film temperature is 60 C. Determine t..

  Refrigerator operates at steady a coefficient of

refrigerator operates at steady a coefficient of performance of 5.0 within a kitchen at 238c. the refrigerator rejects

  Determining the size of the cylinder

An initially empty cylinder is filled with air from 70 F, 15 psia until it is full. Assuming no heat transfer is the final temperature larger, equal to or smaller than 70 F? Does the final T depend on the size of the cylinder?

  Fundamental frequency of vibration of the building frame

If the operating speed of the motor is 1500 rpm, design the girder and the columns such that the fundamental frequency of vibration of the building frame is greater than the operating speed of the motor. Use two beam and two bar elements for the i..

  Changes made to stainlees steel piping to reduce

changes made to stainlees steel piping to reduce intergranular stress corrosion cracking describe four modifications

  What is required capacity on work center 300 for shop

Shop order 7777 is for 600 of part 8900. From the routing file, it is found that operation 20 is done on work center 300. The setup time is 3.5 hours, and run time is 0.233 hours per piece. What is the required capacity on work center 300 for shop..

  Steady-state conditions with negligible inlet velocity

Air enters a well-insulated turbine operating at steady-state conditions with negligible inlet velocity, 4 MPa, and 100°C. The air expands to an exit pressure of 100 kPa. The exit velocity and temperature are 90 m/s and 100°C, respectively. The diame..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd