Calculate the electric field across the resistor

Assignment Help Electrical Engineering
Reference no: EM13276995

The voltage drop across a 1 cm long resistor is 10 V.

a) Calculate the electric field across the resistor;

b) Calculate the work done by the electric field when it pushes a single electron through the length of the resistor

Reference no: EM13276995

Questions Cloud

Find the internal resistance of the function generator : A function generator is adjusted to give a 60 HZ sine wave with no-load (open-circuit) voltage of 3Vrms. When a 1k ohm load is place across the output terminals of the function generator, the output voltage drop to 8Vpp.
Find the internal resistance of the dc power supply : A DC power supply is adjusted to give a no load output voltage of 15 volts with the AC line voltage of 115 volts rms. A full load current of 1A is drawn into the circuit and the output voltage drops to 14.89 volts.
What is the coordinate of the center of mass of the rod : A rod has a linear density ? = 3x, where x is the distance along the rod, What is the coordinate of the center of mass of the rod
Describe the specific security concerns : Describe the specific security concerns or risks that your chosen operating system faces and how you plan to mitigate the risk that each one presents.
Calculate the electric field across the resistor : The voltage drop across a 1 cm long resistor is 10 V. a) Calculate the electric field across the resistor; b) Calculate the work done by the electric field when it pushes a single electron through the length of the resistor
Find the resultant magnetic force exerted by the long wire : Find the resultant magnetic force exerted by the long wire on the square current loop in the figure below if I1 = 8.72 A and I2 = 4.12 A
How many ones did the auctioneer find in the envelopes : A man is going to an Antique Car auction. All purchases must be paid for in cash. He goes to the bank and draws out $25,000. Since the man does not want to be seen carrying that much money, he places it in 15 evelopes numbered 1 through 15. Each enve..
Find the antenna heights assuming smooth earth in between : In an FM line of sight link , the frequency is 6 GHz and the beamwidth = 27 MHz the transmitting and receiving antennas have a gain of 33 dB , the receiving antenna is 40 Km apart from the transmitting station
What color is the last marble : In a box you have 13 white marbles and 15 black marbles. You also have 28 black marbles outside the box. Remove two marbles, randomly, from the box.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Find what is total real power and reactive power produced

A three phase generator is producing power for a balanced load. Each phase provides an rms voltage of 690 V and an rms current of 1000 A. The angle between the voltage and current in each phase is 20 degrees.

  Determine what is the efficiency of the engine

The power measured by a Prony brake attached to an engine flywheel is 3.8 brake horsepower. The indicated horsepower, as measured by means of indicator cards is 4.1. What is the efficiency of the engine

  What is the rms voltage of square wave

A square wave has a max value of 22 volts, a min value of -46 volts, and a frequency of 44 Hz. Note that it is not centered around the t-axis. what is its rms voltage?

  Display and animate a pendulum swinging based on conditions

Write a MATLAB program than can find and plot the pendulum angle as a function of time given an initial swing angle f=f/2. Using the plot command of MATLAB, display and animate a pendulum swinging based on the described conditions.

  Design and simulate a power supply that takes line voltage

Design and simulate a power supply that takes line voltage(120v) and produces a 15V output with less than .5% ripple voltage with the following specifications use either full wave or full bridge wave.

  Where does the energy that was stored in the inductor go

To prevent this, a device is placed across the solenoid (inductor) that can hold the voltage to a safe value, say 40V, during transients. If the activating current in the solenoid is 1 amp and its inductance is 100uH

  Design a microstrip transmission line with z0

Design a microstrip transmission line with Z0 = 100 ohm that will be etached onto a dielectric substrate with er= 3 and a thickness of 4 mm. what should be the width of the microstrip line

  Develop the ow-graph for the fft algorithm from the radix-2

Develop the ow-graph for the FFT algorithm from the radix-2 FFT algorithm for the N = 9 case in which the input is in the bit-reversed order and the output is in normal order.

  Determine the velocity of b relative to a

Racecar A is traveling on a straight portion of the track while racecar B is traveling on a circular portion of the track. At the instant shown, the speed of A is increasing at the rate of 10 m/s2, and the speed of B is decreasing at the rate of 6..

  Find the applied voltage of an iron-core transformer

Find the applied voltage of an iron-core transformer if the secondary voltage is 240 v, and Np = 60 with Ns = 720

  Design 3 stage amplifier with the input signal

Design 3 stage amplifier with the following requirement input signal = 5 mV with R=10k ohms over all gain > 1000 power supply: Vcc = 5V, Vee = -5V Rin > 1 Mega Ohms Rout = 100 ohms 1st Stage BJT must use inverting

  Find snr at the input and snr at the output

We have an amplifier with a 1 MHz bandwidth and a 20 mV input signal. The input noise = 1 mV, output signal 6.0 mV, and output noise = 1 mV. Find: (a) SNR at the input  (b) ..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd