Calculate the electric and magnetic fields in the near field

Assignment Help Mechanical Engineering
Reference no: EM131213099

The Hertzian dipole. A short dipole antenna is 0.02λ long and carries a current of 2 A at 150 MHz. Calculate:

(a) The electric and magnetic fields in the near field.

(b) The electric and magnetic fields in the far field.

(c) The radiation resistance and radiated power of the antenna.

(d) Maximum range in the direction of maximum power density if the time averaged power density required for reception is 10-10 W/m2.

Reference no: EM131213099

Questions Cloud

Is the instrument in the near or the far field : A colleague indicates that this is improper because the measuring instrument is not in the far field of the antenna. Is the instrument in the near or the far field of the transmitting antenna?
Analytical procedures and financial ratios are equivalent : Maricela just got hired by a Big Fouraccounting firm and is currently in"audit boot camp."Her first lesson ison analytical procedures.Maricela studied financial ratios in heruniversity classes, so she feltconfident going into her boot camp training. ..
How will this cop program impact the daily operations of apd : In a time of economic decline, how would you address poverty-stricken populations in your COP program? Explain. What challenges exist with regard to this population, and how might it impact your program? Explain.
Discuss what the liquidity ratios reveal about starbucks : Discuss what the liquidity ratios reveal about Starbucks, including any description of benchmarks, standard measurements, or other types of analysis used once the ratio amount is known.
Calculate the electric and magnetic fields in the near field : Maximum range in the direction of maximum power density if the time averaged power density required for reception is 10-10 W/m2.
Write the answer of given questions : If you're going to rewrite your autobiography, what types of revisions do you plan to make to your own autobiography?
Likelihood of becomingthe dominant design : What are some of the ways a firm can try to increase theoverall value of its technology, and its likelihood of becomingthe dominant design?
Specific behavioral problems of multidisciplinary groups : 1. What are the specific behavioral problems of multidisciplinary groups? 2. Discuss the concept of organizational culture.
State and federal policies ensure access : A number of state and federal policies ensure access to health care for certain groups. Identify and offer your analysis of one such policy.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A three-point bending test is performed on a spinel mgal2o4

a three-point bending test is performed on a spinel mgal2o4 specimen having a rectangular cross section of height d 3.8

  What is the estimated capital investment for ethanol plant

What is the estimated capital investment for a similar ethanol plant with a capacity of 500,000 gallons per year?

  A 10 long cantilever beam having a 4x8 cross-section

a 10 long cantilever beam having a 4x8 cross-section carries a uniformly distributed load of 2000 lbft. sketch the

  Compare the following characteristics of the two propellers

it is proposed to improve the takeoff performance of a single-engined aircraft fitted with a 50-in-diammeter propeller

  Cylinder conditions at the start of compression in an si

cylinder conditions at the start of compression in an si engine operating at wot on an air-standard otto cycle are 60

  Steam at 10 mpa and 450 degrees c enters an adiabatic

steam at 10 mpa and 450 degrees c enters an adiabatic turbine at 80 ms and exits at 10 kpa 92 quality and 50 ms. the

  Calculate the total resistance of the circuit

Calculate the total resistance (RT) of the circuit. Determine the total current (IT) drawn by the circuit. Determine the total power (PT) supplied by the battery.

  The axis of rotation is through the center of the round

an external moment of 500 n-m is applied to the composite plate in clockwise direction as shown. the square plate is

  Find the velocity u2 in the inviscid central core at the

air flows in a horizontal cylindrical duct of diameter d 100 mm. at a section a few meters from the entrance the

  What is the proper ratio for the orifice

We wish to meter the flow with a thin-plate orifice and a differential pressure transducer that reads best at about 55 kPa. What is the proper ratio for the orifice?

  Large plastic casting with thermal diffusivity

A large plastic casting with thermal diffusivity 6.0*10-7 m2/s is removed from its mold at a uniform temperature of 150oC. The casting is then exposed to a high-velocity air stream such that the surface experiences a sudden change in temperature to 2..

  Determine the magnitude of the acceleration of the child

a child a is swinging from a swing that is attached to a trolley that is free to move along a fixed rail. letting l

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd