Reference no: EM13863270
1. An 81 piece gage blocks consists of
9 Blocks =.1001-.1009 in steps of .0001
49 Blocks =.101-.149 in steps of 001
19 Blocks =.05-.95 in steps of 05
4 Blocks =1-4-100 in steps of 1
What pieces would you select to get a length of 2.3797 in. Describe the process of building the height.
2. A 10 in sine bar is shown in the figure below. Determine the process of measuring the angle of the sine bar.
Measurement of Bore Diameter
3. A bore 250.1 mm with a tolerance of ±0.02mm is to be measured by a 200±0.02mm long pin.
a) Show that the diameter can be measured withthe pin shown in the cavity by measuring w. Prove that the diameter of the bore can be expressed by : D=L+(w2/2L)
b) Estimate the minimum and maximumswing, w.
c) Show that the error in diameter may be expressed as:
δD≅ w/L δw+(1-w^2/(2L^2 ))δL
4. The diameter of the bore in a plain ring is measured by laying it on flat surface and placing three 25 mm dia ball equally spaced inside the ring with a 35 mm resting on them. The distance from the surface to the top of the ball is found to be 48.3 mm. Calculate the diameter of the bore of the ring. Describe how would you assess the error in the measurement of the bore diameter .
Measurement of Taper
5. The taper of a bore is measured by placing a 25 mm dia ball and a 40 mm dia ball in the taperbore shown below with gauge block with a 7 mm gage block with 40 mm dia ball and 9 mm gage block with 25 mm gage block . The height H1 and H2 are measured to be 1.12 mm and 50.18 mm. Estimate the taper of the bore.
6. The taper of a bore is measured by placing a 25 mm dia ball and a 40 mm dia ball in the taper bore shown below. The height H1 and H2 are measured to be 1.32 mm and 60.21 mm. Estimate the taper of the bore
7. A Sine bar is used to measure taper in the following set up. Develop an expression for measuring the external nd internal taper shown in the figure and describe how would you do it.
Screw Thread Measurement
8. Figure shows a micrometer measuring dimensions over three wires as shown. Show that the measurement over the wire, M, on a unified thread may be expressed as:
M=Dp-0.866P+3W
Where, Dp=pitch diameter,P=pitch,W=wire dia
|
Describe and discuss reproductive health issue
: Describe and discuss reproductive health issue and blood disorder in terms of detection, prevention, and health promotion;What are some of the social, emotional, or cultural reactions of the health
|
|
What is the value of kw at that temperature
: At a certain temperature, the pH of a neutral solution is 7.73. What is the value of Kw at that temperature
|
|
Product of cellular respiration
: Which of the following is not a product of cellular respiration? water oxygen
|
|
Research and briefly describe a real world
: Research and briefly describe a real world example about how acid raid affects plants. Be sure to demonstrate how pH contributes to the outcome, and proposed solutions (if any). Descriptions should be 2-3 paragraphs and include at least three citatio..
|
|
Calculate the diameter of the bore of the ring
: The distance from the surface to the top of the ball is found to be 48.3 mm. Calculate the diameter of the bore of the ring. Describe how would you assess the error in the measurement of the bore diameter.
|
|
Three questions about mutations in transcription
: Three questions about mutations in transcription/translation sate. 1. A mutation that makes the A-site of the ribosome about 40% less likely to bind to an amino-acyl tRNA 2. A mutation that changes a Threonine (Thr) tRNA anticodon from 3'UGC'5 to 3'U..
|
|
The discovery of cells and microscopic organisms
: Explain the role of the microscope in the discovery of cells and microscopic organisms.
|
|
Food discussion
: Food discussion Homework assignment 2 is to consider the 2 discussion proposals that appear below. Read the 2 proposals and rationales for them. DISCUSSION PROPOSAL 1. We (the U.S government) should give away surplus grain to those countries that c..
|
|
What will your outlook towards maintenance of liquid assets
: What will your outlook towards maintenance of liquid assets to ensure that the firm has adequate cash in hand to meet its obligations at all times?
|