Calculate the density of the exhaust gas

Assignment Help Civil Engineering
Reference no: EM131310550

A new jet engine is being tested in a wind tunnel, as illustrated in the following figure. Air, with standard properties at an altitude of 6000 m, enters the engine at a velocity of 275 m/s through a circular intake port of radius 0.5 m. Fuel enters the engine at a mass flowrate of 2.5 kg/s. If the exhaust gas leaves the engine with an average velocity of 300 m/s through an exit port of radius 0.4 m, calculate the density of the exhaust gas. How would your solution to this problem change if the engine were attached to the wing of an airplane flying through still air at a velocity of 900 km/h?

2253_e70338d2-dcc5-4400-85cf-204769b221c5.png

Reference no: EM131310550

Questions Cloud

Create a server diagram to model the physical view of system : To present a static model of the system, create a diagram for a layered architecture view of the system.Using the components you identified in your layered view of the system, create an activity diagram that shows how a customer would place an ord..
Determine the average fluid velocity at the drain port : Suppose that the pool has a drain port with a diameter 0.5 in. Immediately after the drain is opened, the rate of change of the depth of the water in the pool is observed to decrease to 80% of the value calculated in part (a). Determine the averag..
Determine time required to raise initially ozone free water : Determine the time required to raise the initially ozone-free water in the pond to a concentration level of 0.15 mol/m3.
How many bacteria will be present after ten minutes : The bacteria Escherichia Coli are commonly found in the human intestines. How many bacteria will be present after 10 minutes? 20 minutes? 30 minutes? 40 minutes? And 60 minutes?
Calculate the density of the exhaust gas : calculate the density of the exhaust gas. How would your solution to this problem change if the engine were attached to the wing of an airplane flying through still air at a velocity of 900 km/h?
Determine the kla for oxygen for new dispenser : Determine the KLa for oxygen for this new dispenser when it is operated 3.2 m below the liquid surface with the air flow rate of 7:08 × 10-3 m3/s.
Explain how the orange book is the precursor : Explain how the Orange Book is the precursor to current accreditation and authorization methodologies. Your first task in this project is to review the provided scenario and create the shell for the case study. This case study will be used as the b..
Discuss the performance of the stock over the last year : Discuss the performance of the stock over the last year and offer your thoughts being specific about why the stock has done well or not.
Determine the location of the maximum acceleration : determine the acceleration, noting the local and convective components; and

Reviews

Write a Review

Civil Engineering Questions & Answers

  What is the amount of work claimed

It is claimed that in this process, the air produces 70% of the work that would have resulted from a reversible adiabatic expansion from the same initial pressure and temperature to the same final pressure. Room temperature is 20?C. a. What is the..

  Design the weir structure in order to accommodate the design

To avoid submergence the crest of the weir must be at least 0.05 m above the downstream water depth. Here we can assume that the depth downstream is equal to the normal depth. To simplify calculations we will assume that Cd = 0.7 Water depth over the..

  Plot the exit temperature against the percent excess air

Methane gas (CH4) at 25°C is burned with the stoichiometric amount of air at 25°C during an adiabatic steady-flow combustion process at 1 atm. Assuming the product gases consist of CO2, H2O, CO, N2, and O2,

  Determine the magnitude of the force of the rod on the

Using a forked rod, a smooth cylinder C having a mass of 0.5 kg is forced to move along the vertical slotted path r = 0.5? m, where ? is in radians. If the angular position of the arm is ?

  How much force must he exert to stay submerged on the bottom

When a 60 kg boy floats in the pool 93% of his body is submerged. How much force must he exert to stay submerged on the bottom of the pool to remain fully submerged

  What is the mixed liquor suspended solids concentration

An activated sludge system treats 1500 m3/day of raw wastewater with a BOD of 250 mg/L. The reactor volume is 375 m3. The kinetic parameters were determined to be: x = 3 day-1, Y = 0.55 kg SS/kg cells, and Ks = 150 mg/L.

  What is the magnitude of the average force exerted

A carpenter uses a hammer to strike a nail. Approximate the hammer's weight of 1.8lbs, as being concentrated at the head, and assume that at impact the head is traveling in the -j direction.

  Determine the velocity of the solid sphere

A solid steel sphere with a specific gravity of 7.85 and diameter of 0.02 m is falling at its terminal velocity through water at 25 °C. Using either trial-and-error or a graphical approach, determine the velocity of the sphere

  Determine the minimum green time for each approach

A traffic signal control is being designed for a four-leg intersection on a divided highway with the characteristics shown in the table below. Determine an appropriate length of the yellow interval for each approach and how you will provide it.

  Determine the concentration of the sodium ion in solution

A mass of .525g of NaCl has been added to a cylinder containing water. The cylinder diameter is 1.5in and depth of water in 5inches. Determine the concentration of the sodium ion in solution, showing your ans in units of a) mg/L b) mass % and c) m..

  Which humans can be exposed to toxic chemicals in the

In 1908, H. Chick reported an experiment in which he disinfected anthrax spores with a 5% solution of phenol. The results of his experiment are tabulated below. Assuming the experiment was conducted in a completely-mixed batch reactor, determine the ..

  Determine the percentage of the flow which passes through

A pipe network in the form of a cube is made with twelve identical pipes. Each pipe forms an edge of the cube. If the entire inflow and outflow occurs at two adjacent corners, determine the percentage of the flow which passes through the pipe connect..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd