Calculate the cycle thermal efficiency

Assignment Help Mechanical Engineering
Reference no: EM131242076

Answer the Following Question

A reheat/regenerative power plant produces 500 MW. The steam enters the HP turbine at 120 bar, 500°C and expands to 30 bar. The steam is reheattto 500°C before expanding in the IP turbine to 2 bar Some of the steam is fed to the heater at ar and the balance expands in the LP turbine to 0.05 bar. The heater has a TTD of - 5 K and its drain is pumped forward. The HP, IP and LP turbines have isentropic efficiencies of 90%, 88% and 86%, respectively.

The isentropic efficiency of each of the condensate and drip pumps is 78%.

Sketch the plant layout and plot the cycle on T - s diagram and calculate:

(a) The cycle thermal efficiency

(b) The boiler steam capacity, t/h

(c) The boiler thermal load, MWt

(d) The condenser cooling water, m3/h, for a 7 K temperature rise

(e) The cycle work ratio

Reference no: EM131242076

Questions Cloud

Magnitude of the force of the branch : The toothpick mass was 0.15 g, its speed before entering the branch was 227 m/s, and its penetration depth was 17 mm. If its speed was decreased at a uniform rate, what was the magnitude of the force of the branch on the toothpick?
Describe the new-product strategy you might use : Imagine that you are charged with designing a successor to the Wii. Briefly describe the new-product strategy you might use.
What is the frictional force acting on the disk : a) What is the frictional force acting on the disk? N? b) The disk will slide off the turntable if it is located at a radius larger than 21 cm from the axis of rotation. What is the coefficient of static friction?
Large solar panel on a spacecraft : A large solar panel on a spacecraft in Earth orbit produces 2.5 kW of power when the panel is turned toward the sun.
Calculate the cycle thermal efficiency : Calculate The cycle thermal efficiency - The boiler steam capacity, t/h and the boiler thermal load, MWt and the condenser cooling water, m3/h, for a 7 K temperature rise
Determine the schedule of amortization of ecobv : Determine the schedule of amortization of ECOBV for the years 2011 to 2015.  - Reconstruct the balance for the account "Investment in Sandbar" at December 31, 2015.
Find the range of possible values : a) Find the range of possible values for m2 for which the system will be in static equilibrium.
Prepare a substantive outline detailing the program : This assignment requires that you explore a key aspect of organizational development within a large business setting, and prepare a substantive outline detailing the program that you intend to design, develop, implement, and maintain for the benef..
Is it easier to assess the quality of some goods than others : What assumptions can you make about the ability to assess the quality of goods compared to services? Is it easier to assess the quality of some goods than others? What about for services?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd