Calculate the converter voltage vc1

Assignment Help Electrical Engineering
Reference no: EM13218427

A three-phase inverter is used for interfacing a PV power generator to the grid of 420 VLL (max) and 50 Hz. The per phase input filter inductor LS =2.0mH and the DC-bus voltage is controlled to 740 V. The converter is controlled such that the power angle is 7.44 degree leading and the real power supplied to the grid is 20 kW. The converter supplies reactive power to the grid.

Calculate the converter voltage VC1, reactive power, the converter phase current and modulation index.

 

Reference no: EM13218427

Questions Cloud

Success of shoppers stop : What are the significant factors that have led to the success of Shoppers Stop and draw the typical profile(s) of Shoppers' Stop customer segments.
How much should be deposited : An indiviual wishes to deposit an amount of money now and $100 every six months so that at the end of five years $1500 will have been accumulated. With interest 4% per year, compounded semiannually, how much should be deposited?
Which project to select on the basis of the rate of return : Consider an investment project with the following cash flows: n Porject A Project B 0 -$150,000 -$120,000 1 $30,000 $25,000 2 $25,000 $15,000 3 $120,000 $110,000 A) Compute the IRR for each investment B) At MARR= 15% determine the acceptability of..
Compute volume of swimming pool : Do a calculation to check the claim that to fully neutralize 17,000 tons of CaCO3 would require enough 0.0005 M H2SO4 to fill 8 millions swimming pools.
Calculate the converter voltage vc1 : Calculate the converter voltage VC1, reactive power, the converter phase current and modulation index.
Determine the phase angle between the inverter : Determine the phase angle between the inverter fundamental voltage,VC1, and grid side voltage such that the power delivered to the grid is 10 kW and the fundamental current leads VS by 150°. Calculate the reactive power to the grid and draw the ph..
Calculate the minimum value of vd : Calculate the minimum value of Vd if the power flow through the converter is 5 kW (a) from the ac to the dc side and (b) from the dc to the ac side.
Compute the concentration of salt in solution : The cylinder diameter is 2 inches and the depth of the water in the cylinder is 4 inches. Determine the concentration of salt in solution, showing your answer in the units specified.
Compute the average price increase for gold : Gold cost about $100 an ounce in 1971. In 2007, the cost of an ounce of gold is hovering around $800. compute the average price increase for gold.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Define what is the fm improvement in db

What is the peak frequency deviation of the FM signal? What is the FM improvement in dB?

  Define a set of digital scales is required to measure a load

A set of digital scales is required to measure a load of 1000 N with an accuracy of ±1 N. Determine the minimum output resolution of the required ADC.

  Shielding effectiveness with copper also steel at equality

Shielding Effectiveness with copper and steel at equality, Determine the frequency at which two 1 mm thick shields, one made of copper and the other of steel

  Efficiency of mosfet circuit

Efficiency of MOSFET circuit provide in datasheets of any product is measured at transient state of my output node or staedy state?

  Frequency division multiplexing

Write a short technical report on Frequency Division Multiplexing

  Consider a coffee counter with a single server

Consider a coffee counter with a single server at which tired students arrive according to a Poisson process. Let the mean arrival rate be two students per ten minutes and assume the serving time is exponentially distributed with an average of 180..

  Explain an electric heater is connected to a constant

The Problem: An Electric Heater is connected to a constant 250-V source and absorbs 1000 W. Subsequently, this heater is connected to a constant 210 V source.

  The design must show all stages used in its development

The design must show all stages used in its development and must be implemented and tested in PSpice and suitable timing waveforms produced.

  Explain what is the bandwidth occupied by this signal

What is the bandwidth occupied by this signal, and the noise bandwidth of the receiver for this signal? Find the BER at the receiver output and the average time between errors.

  Use mips assembly language

Write an assembly program to calculate sum of number10 through 25

  Define the gain of the antennas must be increased

The gain of the antennas must be increased when the TDMA system described in part (d) is used because the bit rate is higher than with FDMA and the noise power in the receiver is therefore higher

  Optimum length of the antenna to receive the fm station

Optimum length of the antenna to receive the FM station, An FM radio station transmits at a frequency of 99.9 MHz. A radio receiver has an antenna that is a quarter wavelength monopole consisting of a telescoping rod

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd