Calculate the compressive strength of the concrete

Assignment Help Civil Engineering
Reference no: EM13310660

A concrete cylinder of height 8 inches and diameter of 4 inches was tested in the lab. The maximum compressive force was found to be 150,000 lbs and a tensile force of 25000 lbs.

1. Calculate the compressive strength of the concrete

2. Calculate the tensile strength of the concrete

Reference no: EM13310660

Questions Cloud

Determine the value for cu and the cohesion intercept c : At failure, the respective minor and major principal stress values are 20 kPa and 46 kPa for one and 40 kPa and 80 kPa for sample two. From these data, determine the value for (phi)cu and the cohesion intercept c on the Mohr's circle shear stress ..
How fast is it going when the nose leaves the station : An express train passes through a station. It enters with an initial velocity of 22.0 m/s and decelerates at a rate of 0.150 m/s2 as it goes through. How fast is it going when the nose leaves the station
Determine the detention time within the tubes in minutes : Consider a high-rate sedimentation basin with tube settlers. The basin is 120 feet long and 30 feet wide. The length of the basin covered by tube settlers is 90 feet. The water depth is 15 feet.
Multinational organizational that engages in the dependent : Atlantis Global Corporation (AGC) is a multinational organveloization that engages in the depment, manufacture, and marketing of electronic circuit boards for use in high-definition TV screens. Although the design centers are located in the United St..
Calculate the compressive strength of the concrete : A concrete cylinder of height 8 inches and diameter of 4 inches was tested in the lab. The maximum compressive force was found to be 150,000 lbs and a tensile force of 25000 lbs.
What would be its final velocity : A fictional spaceship accelerates at a constant rate of 0.107 m/s2. What would be its final velocity
What is the station of the pt on a single-lane highway : A Horizontal curve on a single-lane highway has its PC at station 123+70 and its PI at station 130+90. The curve has a super-elevation of 0.06 ft/ft and is designed for 70 mph. What is the station of the PT
Determine what is the stationing of the pc and pt : A horizontal curve is being designed through mountainous terrain for a four-lane road with lanes 10 ft. wide. The central angle is known to be 40 degrees, the tangent distance is 520 ft., and the stationing of the tangent intersection (PI) is 2600..
What is the gauge pressure : A submarine dives to a depth of 310 feet in the ocean. What is the gauge pressure at this depth? How many atmospheres is this

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine moles of helium in cylinder

As the piston is compressed, the pressure also increases by 2000000 Pa. If there is 4 times as many atoms of nitrogen as helium, how many moles of helium are in the cylinder?

  Mixed liquor volatile suspended solids

For a mixed liquor volatile suspended solids (MLVSS) of 1800 mg/L, what is the total return solids flow rate?

  What has been the change in internal energy of the gas

A cylinder with a moveable piston holds .20 lb of hydrogen initially in a volume of 1 cu ft at a tem-perature of 1300 F. Then the volume is expanded to 2.5 cu ft while the gas pressure remains constant.

  Determine the change in the bar thickness of axial load

At an axial load of 23 kN, a 40-mm-wide by 10-mm-thick polyimide polymer bar elongates 2.7 mm while the bar width contracts 0.17 mm. The bar is 240 mm long. At the 23-kN load, the stress in the polymer bar is less than its proportional limit.

  Determine the location of the hydraulic jump

the flow rate is 600 cfs. for a long distance upstream the bottom slope is 2.5%. the bottom slop of the channel abruptly changes to 0.6% and continues at that slope for a long distance determine the location of the hydraulic jump.

  Calculate the density of air flow ate sections 1 and 2

Air flows steadily between two sections in a long, straight portion of 4 in. inside diameter pipe (D1=D2). The uniformly distributed temperature and pressure at each section are p1=100psia, p2=18.4psia, T1=540 R and T2=453 R.

  Compute gravitational force and force of mutual attraction f

two steel spheres 100mm in diameter. Compute gravitational force and the force of mutual attraction F in newtons. the specific weight of steel is 0.284 lb/in^3

  Determine the flow rate per unit width of aquifer

The aquifer is inhomogeneous with K = 12+0.006x, where x =0 at point 1, and the piezometric heads at point 1 and 2 are 14.2 m and 18.8 m, respectively measured above the upper confining layer.

  Determine what percent of particle are retained in clarifier

if the settling velocity of a particle is 2.8 mm/s and the overflow rate of an upflow clarifier is .56 cm/s what percent of the particles are retained in the clarifier

  Determine how much soil must be removed from the site

The minimum safe side slope for an excavation in a certain type of soil is 3 horizontal to 1 vertical. If a foundation excavation must be 40 ft wide x 60 ft long x 20 ft deep, How much soil must be removed from the site

  Determine the normal depth-critical depth and velocity

A PVC pipe with a diameter of 30 inches will carry a flow of 20 cfs. the bottom slope is 0.005 and the roughness coefficient is 0.015. determine the normal depth, critical depth, velocity and the froude number.

  Filter in each filter cycle

a) What flow rate (m 3/s) does the filter handle during production? b) What volume of water is needed for backwashing plus rising the filter in each filter cycle?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd