Calculate the boundary-layer thickness at the end of plate

Assignment Help Mechanical Engineering
Reference no: EM131270847

Several 2-m-wide, 4-m-long thin metal plates are towed for an underwater construction. Assuming the tow vehicle moves at a speed of 2 m/s and the plates are parallel to the free stream, calculate the drag force for a single plate positioned as in cases a and b in the figure. Calculate the boundary-layer thickness at the end of the plate (for the two cases). Assume laminar flow (Blasius solution) and use seawater properties from Table 1.1.

1965_18115386-92b3-4fa6-89da-21cb5ce16838.png

1321_9154a8f0-a417-4496-83cd-b49ccb121a84.png

Reference no: EM131270847

Questions Cloud

Write paper on the major socioeconomic programs : In this essay, students will write a paper on the major socioeconomic programs, the policy behind them, and how socioeconomic programs impact contracting. Students will then analyze one specific socioeconomic program
Where patients have the right to refuse the treatment : What are the conditions where patients have the right to refuse the treatment? Are there any limits to an individual’s choices of treatment, If yes, explain with an example.(use your own words)
Pregnancy discrimination act of 1978 : Pregnancy Discrimination Act of 1978. In the event that a woman learns she is in the early stages of her pregnancy (not yet showing) , is she required to disclose to her potential employer that she is pregnant? Why or Why not?
Internal alignment policies and techniques : How might a company's business strategy affect the internal alignment policies and techniques of its Total Compensation system?
Calculate the boundary-layer thickness at the end of plate : Calculate the boundary-layer thickness at the end of the plate (for the two cases). Assume laminar flow (Blasius solution) and use seawater properties from Table 1.1.
Relationship between conflict and group member diversity : What are some of the major differences between a virtual and traditional organization? What are the relationship between conflict and group member diversity. The HAC Reduction program is designed to encourage hospitals by reducing what ?
Assigned an important project : You really want to be assigned an important project but worry that your boss will not give it to you. Your boss has expressed concern lately about your ability to complete some less significant tasks. You are upset and feel these tasks are beneath..
Describe your chosen architecture pattern : Describe your chosen architecture pattern. Explain why you selected the architecture of this case study. Explain how your chosen pattern could be applied to this case study.
Healthcare providers have different view of health care law : Do healthcare providers have a different view of health care law than the general population? Is one more skewed than the other and why ?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The ball is in contact with the racket for 325 if the

a tennis racket hits a tennis ball with a force of where 1230 500 and is the time in milliseconds. the ball is in

  Transient heat conduction

A pure copper sphere of radius 1 cm is dropped into an agitated oil bath that has a uniform temperature of 130C. The initial temperature of copper sphere is 20C.

  Simple inverting comparator circuit with hysteresis voltage

Design a simple inverting comparator circuit with a hysteresis voltage of 120 mv and adnominal threshold of +2.5 V. indicate component volues. A sensor provides temperature data as 360 mv/ c. Develop a comparator circuit that goes high when the tempe..

  Determine the rate of heat transfer out of the condenser

An air-conditioner which uses refrigerant R134-a operates on the Carnot refrigeration cycle. Determine the rate of heat transfer (kW) out of the condenser. Determine the power input (kW) to the compressor.

  Calculate enough points and plot a time-temperature graph

A 35lb block of tin is to be heated from room temperature to a relevant temperature for casting, Calculate enough points and plot a time-temperature graph if the heating is provided by a 5kw electric heating element with 70% efficiency.

  The front of a jet engine acts as a diffuser receiving air

the front of a jet engine acts as a diffuser receiving air at 900 kmh -5degc 50 kpa bringing it to 80 ms relative to

  Temperature deratings in addition to the options you

you are looking for a power unit to run an irrigation pump in your operation. the pump requires 92 horsepower to turn

  A nonwetting metal surface that is at temperature ts -15

a small water droplet of diameter d100 micro meter and temperature tmp 0 deg c falls on a nonwetting metal surface

  Indicate a practical application of this device

Also, a current limiting resistor of 20 kΩ is available for the base of the BJT and a resistor of 200 Ω is available in series with the power supply and the LED. Indicate a practical application of this device.

  Assume that the charge cooler incoming cooling water

Assume that the charge cooler incoming cooling water is at 45 oC and its effectiveness is 80% and the air pressure loss in charge cooler is 10 kN/m2, calculate the air temperature and density at the outlet of the charge cooler. Estimate the % increas..

  How many engagement points on the flywheel

How many engagement points on the flywheel would be necessary to make this machine safe?

  The heating continues so the piston compresses the spring

a cylinderpiston arrangement contains water at 105 c 85quality with a volume of 1l. the system is heated causing the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd