Calculate the average velocity of the flow leaving

Assignment Help Civil Engineering
Reference no: EM13532254

1.Water enters a cylindrical tank through two pipes at rates of 250and 100 gal/min. If the level of water in the tank remainsconstant, calculate the average velocity of the flow leaving thetank through an 8-in. inside-diameter pipe.

2.Water at 0.1 m^3/s and alcohol (SG=0.8) at 0.3 m^3/s are mixed in ay-duct. What is the average density of the mixture of alcoholand water?

Reference no: EM13532254

Questions Cloud

Hold the cratefrom sliding down the plane : It is desired to obtain dynamic similarity between 3 cfs of water(ρ = 1.94 slug/ft3, μ= 2.735 x 105Ibs/ft2) flowing in a pipe and oil 9s.g = 0.91, μ=12 x 105 ibs/ft2) flowing in a 12in diameterpipe at a velocity of 25 ft/s at 90 deg F. What size of p..
How much calcium chloride will react with 100mg of soda ash : A 2.5hr long uniform rainfall resulted in arunoff hydrograph that has the shape of an equilateral triangle.The base of the triangle is 64hr; the peak flow is 535cfs; thedrainage area is 5.7mi^2. Determine the corresponding unithydrograph if the base ..
Determine the speed of each disk after the collision and the : Three cylinders from the same mix were tested for strenght.  Cylinders A and B were cast in 4x8 molds while cylinder C was cast in a 6x12 mold.  The total loads were as follows; cylinder A= 65,200 lbs.,  cylinder B= 68,550 lbs., cylinder C= 151,190 l..
Determine the final velocity of each car : The coefficient ofrestitution between each car is 0.8 . Determine the final velocityof each car, after all impacts, assuming (a) cars A and C hit Car Bat the same time, (b) car A hits car B before car C does.
Calculate the average velocity of the flow leaving : Water enters a cylindrical tank through two pipes at rates of 250and 100 gal/min. If the level of water in the tank remains constant, calculate the average velocity of the flow leaving thetank through an 8-in. inside-diameter pipe.
Draw a psychrometric diagram labeling the system states : A laboratory space has a heat gain of 3 tons with a sensible heatfactor of 0.7. The indoor design conditions are 78 F at 40% RH. Theoutdoor air design conditions are 95 F at 50% RH. The coolingequipment has a fixed air flow rate of 350 cfm/ton of coo..
Determine the water level in the upstream manhole that would : A circular manhole cover has a weight of 250 N and a diameter of 1meter. Surcharged conditions (this means the sewer is flowing full)have developed in the sanitary sewer
Define your coordinate system : A trapezoid has a bottom width of b, and top width of T, a heightof h, and side slopes of z(horizontal to vertical). By integration, determine the location of the centroid of thetrapezoid Define your coordinate system.
Determine the change in kinetic energy and the power output : Steam flows steadily through an adiabatic turbine. Theinlet conditions are 10 MPa, 450 C and 80 m/s. and the exitconditions are 10 kPa, 92% quality at 50 m/s.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the maximum bending stress in the strap

An L2 steel strap having a thickness of 0.125 in. and a widthof 2 in. is bent into a circular arc of radius 600 in. Determine the maximum bending stress in the strap.

  How many days would wastewater take to fill the lagoon

a lagoon is 20 ft by 80 ft with a depth of 5.5 ft .Wastewater from households flow into the lagoon at 260 gal/day .How many days would it take to fill the lagoon

  Discuss how relative motion is critical issue in the midair

Discuss how relative motion is a critical issue in the midair refueling of aircraft. Would control of this process be with the pilot of the tanker or the aircraft being refueled

  Determine the pressure at stagnation point on the nose

determine the pressure at stagnation point on the nose of the airplane. also determine the manometer reading h for the manometer attached to the static pressure tap within the test section of the wind tunnel if the air velocity

  Calculate the required compressive strength

calculate the required compressive strength for a concrete mix design if f'c = 5000 psi and data indicate a standard deviation of 600 psi based on 15 tests for a similar concrete mix.

  Determine the maximum shearing stress in shaft

Ends A and D of the two solid steel shafts AB and CD are fixed, while ends B and C are connected to gears. Knowing that a 4-kN(m) torque T is applied to gear B, determine the maximum shearing stress (a) in shaft AB, (b) in shaft CD.

  How fast was the car traveling before applying the brakes

The vehicle was estimated to hit the light pole at 30 mph. The skid was 650 feet long. How fast was the car traveling before applying the brakes

  Determine the max rimpull of the tractor in each gear

A pneumatic-tired tractor with a 354 - hp engine has a maximum speed of 3.6 mph in 1st gear. Determine the max. rimpull of the tractor in each gear if the engine effieicency is 91%.

  How to determine the efficiency of the pump

Water is pumped at a rate of 1.57 cfs from one large open tank into another through a 6 in diameter cast iron pipe 400 ft long. The water level in the second tank is 160 ft above the level of the first tank and the discharge end of the pipe is sub..

  Determine the velocity of the cart while girls are walking

The 90-lb boy and 75-lb girl wald towards eachother with constant speed on a 330-lb cart with frictionless wheels. assume that the cart was at rest befor the boy and girl start walking.

  Determine the torque t-shear force v and bending moment

Determine the torque T, shear force V, and bending moment M for the following gage readings: 450, 325, 550, and 675 all in microns for gages A through D, respectively. Gages A on side, B on top, C on back side, D on bottom.

  Determine the tension in cables ac and ab

The casting has a mass of 3 Mg. Suspended in a vertical position and initially at rest, it is given an upward speed of V mm/s in 0.3s using a crane hook H. Determine the tension in cables AC and AB during this time interval if the acceleration is ..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd