Calculate the amount of work done if the process is consider

Assignment Help Civil Engineering
Reference no: EM13564842

1.Determine the minimum height on the wall to which the firefighter can project water from the hose, so that the water strikes the wall horizontally. The speed of the water at the nozzle is Vc=48ft/s. Distance from the hose to the wall is 30ft. and vertical distance from the ground to the hose is 3ft. No angle is given.

2.A container with a plunger compresses one pound mole of an ideal gas from 1 atmospheres pressure to 10 atmospheres. Calculate the amount of work done if the process is considered to be polytropic. Assume the temperature to be 273K and the value of k for the process to be 1.4. All losses are neglected.

Reference no: EM13564842

Questions Cloud

What is the final temperature of the lead bulle : A 5 gram bullet traveling in 20 0C air at 300 m/sstrikes a flat steel plate and stops. What is the final temperature of the lead bullet
Calculate the equivalent horizontal and vertical hydraulic : What is the velocity of the blocks 5.00 after the blocks have started moving? Assume that the rope joining the two blocks in long enough so that, at this time, block A is on the frictionless surface while block B is still on the rough surface.
Evaluate the period at which it oscillates : A cart of mass 250 g is placed on africtionless horizontal air track. evaluate the period at which it oscillates
Determine the magnitudes of the velocity and acceleration : Three stock car drivers are racing around a circular bend. They are each circling the bend at different radii: r(1)=249 m , r(2)=255 m , and r(3)=261 m . At a given instant, all three are traveling at the same transverse rate of rotation, .259 rad/s ..
Calculate the amount of work done if the process is consider : A container with a plunger compresses one pound mole of an ideal gas from 1 atmospheres pressure to 10 atmospheres. Calculate the amount of work done if the process is considered to be polytropic. Assume the temperature to be 273K and the value of k ..
What average thickness must the engineer build to meet these : An engineer uses a standard technique for measuring the thickness of a clay landfill liner that has a typical standard deviation of 0.7 in. The project specifications require the liner thickness to be 36 inches or more, at least 95 percent of the tim..
Determine the size of the beam with the least cross-section : A simple beam of Douglas-Fir Larch, select grade, has a span of 18 ft with two concentrated loads of 3 kips each placed at the third points of the span. Neglecting its own weight, determine the size of the beam with the least cross-sectiona; area bas..
Calculate the depth of flow upstream of the bridge assuming : A tensile test was performed on a metal specimen having a circular cross section with a diameter of 0.50 inch. The gage length is 2 inches. For a load of 13.5 kips, the elongation was 4.66 x 10-3 inches. If the load is assumed to be within the linear..
Find which dam would need to be constructed more strongly : If a large lake is held back by a dam that is equallylong and equally deep compared to another body of water, but is anarrow river, which dam would need to be constructed more strongly

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the radius of influence of the pumping

A well with a radius of 0.5 m pumps at a constant rate of 1240 m3/day. After the cone of depression has achieved equilibrium, the piezometric heads at two observation wells 40 and 95 m from the pumping well are measured as 78.9 and 83.4 above sea ..

  Determine the tension in each of the cables at a time when

A long trough is supported by a hinge along its lower edge and a series of horizontal cables attached to its upper edge. Determine the tension in each of the cables, at a time when the trough is full of water.

  Find what is the gage pressureat the bottom of the tank

Water occupies the bottom 0.8 m of a cylindrical tank.On top of the water is 0.3 m of kerosene, which is open to the atmosphere. If the temperature is 20 degrees C, what is the gage pressureat the bottom of the tank

  Discuss the applicability of grouting technology inimproving

Rock masses that donot have the desired properties for a givencivil engineeering application are improved. The method of choicedepends on the purpose for which the rock mass is intended. amongthe common methods for increasing the strength of fissured..

  Determine the discharge of a trapezoidal concrete channel

Determine the discharge of a trapezoidal concrete channel section with a bottom width of 4 ft and side slopes of 2:1. The depth of flow is 5 ft and the channel slope is 0.5%

  Using present worth analysis which process should b selected

The operating cost will be $10,000 per quarter with a salvage value of $25,000 after its 2-year life. Process B will have a first cost of $250,000, an operating cost of $15,000 per quarter and a $40,000 salvage value after its 4-year life.

  What will be the new height of fluid column

A u-tube manometer is used to measure the pressure of a vessel under vacuum. Assume the manometer is open to atmospheric pressure (101.325 kPa) and the density of the fluid in the manometer is 12.0 g/cm3.

  Determine elevation of point b from the elevation of a point

To determine the elevation of a point B from the elevation of a point A, which is 511.6 ft. When the transit was set up over the point A, the height of the transverse axis above that point was 4.92 ft.

  Is the calcite precipitating or dissolving in the pore water

A ground water sample has a pH of 7.5, hardness (due to primarily Ca2+) of 100 mg/L, and an alkalinity of 250 mg/L as CaCO3(s). Is the calcite precipitating or dissolving in the pore water

  Determine present worth of costa for purchasing the analyzer

At the end of the first 5 years, the company upgraded the analyzer at a cost of $10,000. Following the upgrade the lab purchased another 5 year maintanence contract for $1000 a year, payable at the end of each year.

  Smallest standard commercial pipe

For satisfactory operation, the static pressure at the pump inlet must not be lower than -6 m of water gage. Determine the smallest standard commercial pipe that will give the required performance.

  What is the percent change in pressure that a scuba diver

What is the percent change in pressure that a scuba diver in salt water will feel going from 50 to 40m of depth? What is the percent change from 10m to the surface? Use absolute pressure and assume standard atmospheric conditions. Would the answer ch..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd