User Account

All Pages

Calculate the allowable tensile load

Assignment Help Mechanical Engineering
Reference no: EM131382394

A single-shear lap joint is to have fasteners arranged on three gage lines, similar to the joint shown in Figure 19.12 . The steel plates are to be of ASTM A36 steel.

Write a program that will calculate the allowable tensile load for such a joint assuming 3 4 -in.- diameter A325-X high-strength bolts.

Input is to be the number of bolts, which must be in multiples of three, and the cross-sectional dimensions (width and thickness) of the main plates. Assume standard holes.

1385_Fig01.jpg

Reference no: EM131382394

Questions Cloud

What’s the probability that chuck is on the job : You go to Dan's for supper one night and hear a dish break at the sink. What's the probability that Chuck is on the job?
What is the probability that leah’s first flight was delayed : Are the first flight leaving on time and the luggage making the connection independent events? Explain.
What percent of freshmen eventually graduate : Is there any evidence that a freshman's chances to graduate may depend upon what kind of high school the student attended? Explain.
Created a list of expenses by category for each employee : You created a list of expenses by category for each employee for the last six months. Now you want to subtotal the data to review total costs by employee and then create a PivotTable to look at the data from different perspectives.
Calculate the allowable tensile load : Write a program that will calculate the allowable tensile load for such a joint assuming 3 4 -in.- diameter A325-X high-strength bolts.
Calculate the allowable tensile load for the butt joint : Calculate the allowable tensile load for the butt joint shown. The fasteners are 7 8 -in.-diameter A325 high-strength bolts in a slipcritical connection (A325-N). The plates are of ASTM A36 steel.
How many red lights should she expect to hit each day : Red lights. A commuter must pass through five traffic lights on her way to work and will have to stop at each one that is red.
Calculate the allowable tensile load for the lap joint shown : Calculate the allowable tensile load for the lap joint shown. The fasteners are 25-mm-diameter A325-X high-strength bolts. The plates are ASTM A36 steel.
Calculate the allowable tensile load for the butt joint : Calculate the allowable tensile load for the butt joint shown. The fasteners are 20-mm-diameter A325-N high-strength bolts and the plates are ASTM A36 steel.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the magnitudes of the student velocity

The student starts from rest at the caller and runs away with a constant radial acceleration 0.5 m/s2 (with respect to the platform) as shown. The platform rotates at constant angular velocity 0.2 rad/s. Determine the magnitudes of the student's ve..

  Using the finite difference mesh delta

Consider a two- dimensional, straight triangular fin of Length L= 50mm and base thickness t= 20mm. The thermal conductivity of the fin is k= 25 W/mK. The base temperature is T_b= 50 degrees Celsius, and the fin is exposed to convection conditions cha..

  Determine the compressive stress at the cross section

Determine the compressive stress at the cross section of the base, B, and at the cross section, A, half way up the cone, and compare the compressive stress at B with the compressive stress at A. The volume of the cone is Vcone = (1/12) πd2h.

  Compute the reactions and draw the shear and moment curves

Compute the reactions and draw the shear and moment curves for the beam in Figure. Also E = 200 GPa and = 120 X 106 mro4 Use symmetry to simplify the analysis.

  What is the maximum angular speed at which the particle can

a light inelastic string of length 1.5m fixed at one end carries a particle p of mass 4 kg at the other end. if the

  Given a rectangular sample of ductile iron 60-40-18 with

given a rectangular sample of ductile iron 60-40-18 with cross sectional dimensions 0.8 in x4 in calculate the stress

  Determine the angle through which end d of shaft cd rotates

In the gear-and-shaft system shown, the shaft diameters are dab= 2 in. and dcd=1.5 in. Knowing that G = 11.2 x10^6 psi, determine the angle through which end d of shaft cd rotates.

  Literature review on high speed machining

Report on High speed machining on duplex stainless steel. In that report I need literature review on High speed machining.

  Is the supervisor''s position here ethically justifiable

You are a supervisor for a complex design project, and are aware of the NCEES code rule according to which engineers may coordinate an entire project provided that each design component is signed or sealed by the engineer responsible for that desi..

  Sketch the resultant in the xyz coordinate system

For each vector, find the direction angles and write an expression for the vector using Cartesian representation. Evaluate the sum of the two vectors, and report the direction angles for the resultant. Also, sketch the resultant in the xyz coordin..

  A simply supported beam loaded by two forces

Select a pair of structural steel channels mounted back to back to support the loads in such a way that the deflection at midspan will not exceed 1/ 16 in and the maximum stress will not exceed 6 kpsi. Use superposition.

  Estimate the value of v2/c2 for which krel differs

By expanding Krel/Kcl in powers of v2/c2, estimate the value of v2/c2 for which Krel differs from Kcl by 10 percent.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd