Calculate the adiabatic flame temperature

Assignment Help Mechanical Engineering
Reference no: EM13216836

Calculate the adiabatic flame temperature (at constant pressure) for ethane C2H6 in air:

(a) at the lower flammability limit (XL ¼ 3:0%) and
(b) at the stoichiometric mixture condition.
Assume constant specific heats for all species (1.1 kJ/kg K) and use the data from Tables 2.3
and 4.5. The initial state is 1 atm, 25 C and the initial mixture density is 1.2 kg/m3.

 

Reference no: EM13216836

Questions Cloud

Uniform crime report and self-report data : Complete the matrix below. To complete this matrix, list two pros and two cons of Uniform Crime Report (UCR) data and two pros and two cons of self-report data.
What is the proeutectoid phase : Consider 6.0 kg of austenite containing 0.45 wt% C, cooled to below 727 degrees Celcius (1341 degrees Farenheit).
How increasing the attractiveness of the debt securities : Both convertibility and warrants attached to debt aim at increasing the attractiveness of the debt securities and lowering the interest cost.
Determine the amount of heat that must be removed : A vessel with a volume of 0.0011 m3 is filled with dry saturated steam at a pressure of 95 kPa. It is then sealed and cooled to 250C. Determine the amount of heat that must be removed.
Calculate the adiabatic flame temperature : Calculate the adiabatic flame temperature (at constant pressure) for ethane C2H6 in air
State political practices-impact human resource management : When businesses operate across countries, how does diversity-in cultures, socioeconomic factors, or political practices-impact human resource management?
How many engagement points on the flywheel : How many engagement points on the flywheel would be necessary to make this machine safe?
Different marginalized populations : What would you say is the overall lesson from the simulation activity? How do you improve communication between caregivers and patients with low health literacy? Patients with disabilities? Children?
Describe the main kinds of social mechanisms : Describe the main kinds of social mechanisms that are used by people to communicate and collaborate.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the magnitude of its total accleration

determine the magnitude of its total accleration when (a) t=0 and (b) t=2 Whats the solution.

  Find the compression ratio

Find the compression ratio, cutoff ratio, the thermal efficiency, the mean effective pressure, and the P -v and T-s diagrams clearly showing all corners.

  Calculate the rocket power

rocket boosts the speed of a spacecraft from 7500 m/s to 10 500 m/s with a thrust of 890 kN. Calculate the rocket power.

  How penalty method is applied on a one dimensional

how penalty method is applied on a one dimensional heat equation in Meshless method.

  Determine the largest allowable square cross

Determine the largest allowable square cross section of a steel shaft of length 6 m if the maximum shearing stress is not to exceed 135 MPa

  Calculate the contact forces at a and b

the 50-kg homogeneous smooth sphere rest on the 30 degree incline A and bears against the smooth vertical wall B. calculate the contact forces at A and B.

  Determine the resultant of the three forces

Determine the resultant of the three forces F1 = 2.0i + 3.3j - 2.6k; F2 = - i + 5.2j - 2.9k; and F3 = 8.3i - 6.6j + 5.8k, which are concurrent at the point (2, 2, -5.). The forces are in Newton's and the distances are in meters.

  Determine the heat transfer coefficient for laminar flow

Determine the heat transfer coefficient for laminar flow over this cylinder. First, at your discretion, select an available set of experimentally obtained data from the literature. Then, this would provide you with a set of Reynolds numbers.

  Calculate the maximum permissible crack size

calculate the maximum permissible crack size in acenter cracked panel subjected to a unifrom stress of 20 ksi. the toughness is 50 ksi"in, the yield stress is 60 ksi, w=12 inches

  Ways to ensure relevant base and safety loads

All calculations and assumptions must be provided together with a full explanation of all the terms

  What is differential levelling

What is differential levelling? list the procedure for carrying out a differential levelling exercise where one point is beyond the range of the instrement . 100 word limit

  Module fea - finite element analysis

Module FEA - FINITE ELEMENT ANALYSIS ,  Provide answers to all questions. Note that assignment part 2 carries 60% of the marks for the course.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd