User Account

All Pages

Calculate the actual power transmitted to the second pulley

Assignment Help Mechanical Engineering
Reference no: EM13550009

QUESTION 1

A pulley 150 mm diameter is driven directly by an electric motor at 250 revs min-1. A V-belt is used to transmit power from this pulley to a second pulley 400 mm diameter against a load of 200 Nm.

The distance between the centre of the pulleys is 600 mm, the included angle of the pulley groove = 40°, the coefficient of friction between the belt and pulley is 0.4 and the ultimate strength of the belt is 8 kN.

(a) Calculate the actual power transmitted to the second pulley.

(b) Calculate the power which can be transmitted if the maximum tension in the belt is limited to half of the ultimate strength of the belt.

(c) What would be the effect of the following factors on the maximum power which can be transmitted (give reasons for your answer):

(i) increasing the coefficient of friction

(ii) increasing the included angle of the pulley groove.

(d) What would be the effect on the following if the load torque is increased and the speed maintains constant (give reasons for your answer):

(i) the tension in the tight side of the belt

(ii) the tension in the slack side of the belt

(iii) the power transmitted.

Reference no: EM13550009

Questions Cloud

Specify efficiency of the gear train as a percentage : Determine an equation for the efficiency of the gear train in terms of the load (torque) on shaft 2 and determine the input power required at shaft 1.
Describe amount of energy in joules and btu : A family used 1,438 kilowatt hours (kwh) of electricity during the month of October. Express this amount of energy in joules and Btu.
Estimate what is the acceleration of the elevator : A 76-kg man standing on a scale in an elevator notes that as the elevator rises, the scale reads 817 N. What is the acceleration of the elevator in m/s^2 upward
Determine the tension in the cord : An object of mass M = 15.0 kg is attached to a cord that is wrapped around a wheel of radius r = 12.0 cm and mass m = 50.0 kg. The object slides down a frictionless incline which makes an angle ? = 40.0° with the horizontal. Assume the axle of the..
Calculate the actual power transmitted to the second pulley : Calculate the actual power transmitted to the second pulley and calculate the power which can be transmitted if the maximum tension in the belt is limited to half of the ultimate strength of the belt.
Explain the gulf coast of louisiana and mississippi : Hurricane Katrina, which hit the Gulf Coast of Louisiana and Mississippi on August 29, 2005, had the second lowest ever recorded barometric pressure at 920 mb.
Determine what is the magnitude of the resultant force : A 13.0-kg object undergoes an acceleration of 1.5 m/s^2. What is the magnitude of the resultant force acting on it
Find the speed of the electron and speed of the proton : The rest energy of an electron is 0.511 MeV. The rest energy of a proton is 938 MeV. Assume both particles have kinetic energies of 1.80 MeV. (a) Find the speed of the electron. c (b) Find the speed of the proton. c
Define what mass can the balloon lift at sea level : What mass can the balloon lift at sea level, where the density of air is 1.22 kg m-3. What would be the payload if He were used instead of H2

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd