Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
A BJT is being used as a switch and is triggered whenever thebase-emitter voltage v(t) rises above 0.15 volts. The voltage v(t)is sinusoidal and changes according to v(t )= 0.23cos( 100π t)+ 0.16sin(100π t + 0.4) .a) Express v(t) a sine function only (use trigonometric identities).b) i) What other method can be used to obtain expression ina)? Obtain the same expression using this method.ii) Why does this other method fail if it is used to find a single expression forv 2 ( t ) =0.23cos(100 πt ) +0.16sin(200 πt )while it works fine forv(t) = 0.23cos(100πt) + 0.16sin(100πt)c) Using the expression in a), calculate the percentage timeper cycle the BJT is in cut-off mode.
Design an excess-2 code converter to drive a seven-segment indicator . the four inputs to the conducter circuit is (A,B,C, andd) represent it in Excess-2 code decimal digit. the inputs aredigits 0-9, so the six unused combinations are dont cares.
The data inputs I0 through I7 are wired as follows: I0 = I1 = 0, I2 = I6 = , I3 = I5 = I7 = 1; and I4 = D. (a) Determine the Boolean function that the MUX implements. (b) Implement the function using a 4×1 MUX with minimum extra logic gates.
Design a system using either a flow diagram or pseudo code that will accept a block of data words encoded as specified in Part 1; then check the parity for each data word and for the block. The system should output each of the 8-bit data words.
Suppose a car is traveling at +23.2 m/s, and the driver sees a traffic light turn red. After 0.563 s has elapsed (the reaction time), the driver applies the brakes, and the car decelerates at 7.00 m/s2. What is the stopping distance of the car
The x-y plane separates dielectric material with εr1=2.0 (for z
calculate the capacitance of the capacitor and the inductance of the inductor. for the capacitor it's going to be 1/(j*2*pi*frequency*capacitance) and (j*2*pi*frequency*inductance) for the inductor but what are the valves for the capacitance and ..
Desired D.C. Output : 10 V Load Variation: 0.3 kilo-ohms - 10 kilo-ohms Ripple Factor: Less than 0.1% for 2 kilo-ohms load Load Regulation: Better than 3 mV for a 1 mA change in load current
A 480 V, three phase system is supplying a 10kW heater and a 5kVAR cap bank. draw the power triangle and calculate the line current
Given a 1-phase 50 kVA 12.47 kV pf = 0.8 lagging static load a. Modeling the load as constant complex power, determine the correct value for S and I. b. Modeling the load as constant complex impedance, determine the correct value for Z and I.
An LTID system frequency response over |omega|
Suppose we have a secret message that is 105 BINARY digits long. What is the smallest power of 2 needed to generate a binary codeword long enough for this message What is the maximum number of binary digits that can be generated with this choice o..
Assume the temperature is 300K and mobilities are u_n = 1300 cm^2/Vs and u_p = 450 cm^2/Vs. a. What are the majority and minority carrier concentrations b. What is the resistivity of the sample c. What is the resistance (end-to-end) of the sample
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd